Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Traces of Coffee Grounds in New Machine? This is normal! Grinder was tested during assembly with beans. Despite cleaning, traces of ground coffee may be found. SelectorSwitchSteamPortionPermanentSteamON/OFFRinseSELECTPRODUCTFourCoffeeButtonsALACarteRotaryDialwithPush-Button RED TEXT represents display text. A) First Time Ever Preparation 1. Fill water in tank and beans in bean container. 2. DO NOT install the Clearyl Filter Cartridge now! 3. Push the main power switch in the back of the machine. 4. Push the ON/OFF button in the display. When the display reads FILL SYSTEM / PRESS STEAM place a cup under the frother and push the PERMANENT STEAM button. SYSTEM FILLING then HEATING UP. 5. PRESS RINSE. Place a cup under the coffee spouts and press the RINSE button. MACHINE RINSING. SELECT PRODUCT. 6. Place a large cup underneath the coffee spouts and press the 1-CUP coffee button. 1 COFFEE: The machine starts grinding and brewing. Repeat once. Discard the first two cups of coffee. B) Daily Preparation 1. Fill fresh water in tank and check bean container. 2. Push ON/OFF button. HEATING UP. PRESS RINSE. Place a cup under the coffee spouts and press the RINSE button. MACHINE RINSING. SELECT PRODUCT. Important: You can only brew coffee when display shows SELECT PRODUCT C) Grinding and Brewing Coffee Four pre-set coffee buttons: 1 ESPRESSO, 2 ESPRESSI, 1 COFFEE, 2 COFFEES. These buttons are pre-set for strength (five settings), cup size (1 to 8 oz. per cup) and temperature (HIGH, NORMAL) During brewing you can over- ride the cup size by turning the ROTARY DIAL. Cup size for 2-cup buttons is shown PER CUP! In programming you can change all three functions. Important: You can always stop the flow of coffee by pushing any of the coffee buttons. A LA CARTE button. Push the button and change the strength by turning the ROTARY DIAL (XMILD, MILD, NORMAL, STRONG, XSTRONG). Now push the ROTARY DIAL. During grinding turn the Dial to set the cup size. D) Changing the Grinder Fineness Important: You can only adjust the fineness during the actual grinding process. 1. Open the bean container lid and turn the dial while grinding: larger dots: coarser; smaller dots: finer. 2. For darker, oily beans, grind somewhat coarser. For lighter beans, grind somewhat finer. E) Using Hot Water (factory setting is 5 oz.) Place a cup underneath the Hot Water Spout and turn the SELECTOR SWITCH to the right. WATER PORTION. To stop the hot water flow turn the SELECTOR SWITCH to the left. F) Frothing and Steaming with the DUAL FROTHER PLUS (Using the frothXpress PLUS system see section "N"). Important: All frother parts must be tightly connected and clean. 1. Cappuccino: One shot espresso plus ~4 oz. of steamed and frothed milk. Metal frother sleeve DOWN. 2. Latte: One shot espresso plus ~4 to 5 oz. of steamed milk. Metal frother sleeve UP. 3. If the red lights in the steam buttons are ON, immerse the frother into a pitcher with milk and push the PERMANENT STEAM button. DRAW OFF STEAM. Steam pushes into the milk ( if the steam buttons are not illuminated, see chapters 16.6 Operating Instructions). a) Push the STEAM button to stop. SELECT PRODUCT. To continue steaming push the STEAM button again. b) After steaming you can immediately brew coffee. Important: Knocking Noise during Frothing: The machine pumps water droplets for steam. This is normal. Please note: Skim and 1% milk will produce more froth than 2% and regular milk. To increase milk temperature, frother sleeve should be UP. G) Cleaning the Frother Should be done right after use, takes less than 15 sec.! Place a large cup underneath the frother. Push the PERMANENT STEAM button. After 5 sec. push the button again to stop. H) Programming Factory Settings: • 1-cup Espresso: 2 oz., strong • 2-cup Espresso: 2 oz./cup, strong • 1-cup Coffee: 5 oz., strong • 2-cup Coffee: 5 oz./cup, strong • All cup buttons are set to temperature HIGH. • Hot Water: 5 oz. • Steam Portion: 14 seconds All other settings see chapter 5, Operating Instructions. • Open Front Cover and push and hold the ROTARY DIAL FILTER NO. • Slowly turn the Dial clockwise to scroll through the following functions after FILTER NO: HARDNESS, RINSE, POWDER QUANTITY (strength), WATER QUANTITY (cup size), TEMP, WATER PORTION, STEAM PORTION, ECONOMY, TIME, UNIT ON, OFF AFTER, LANGUAGE, DISPLAY, INFO, EXIT. • To exit programming choose EXIT and push the ROTARY DIAL: SELECT PRODUCT. Programming Coffee Strength / POWDER QUANTITY Here is how to change the coffee strength for the 1-cup coffee button: • SELECT PRODUCT, push and hold the ROTARY DIAL, FILTER NO. • Turn the Dial until display shows POWDER QUANTITY. • Push the Dial to get into the function. SELECT PRODUCT. • Push the 1-cup coffee button: STRONG. • Turn the Dial to select (example) MILD. • Push the Dial to confirm and turn the Dial to EXIT. • Push the Dial: SELECT PRODUCT. From now on the 1-cup coffee button will brew MILD coffee. I) Installing the Clearyl Cartridge Important: Never inst...