Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Kalorik Dateigröße: 426.12 kb Dateiname: Unterrichtssprache:

If you want to grind coffee to prepare only 1 to 4 cups of coffee, press the 1-4 cup button. It will reduce the time of grinding coffee to 20 seconds instead of 30 seconds for 5 to 10 cups (default setting). NOTE: you cannot select the 1-4 cup setting if you have switch off the coffee grinder by pressing the GRIND OFF button. Place the coffee grinder correctly on its shaft. Close the lid of the coffee grinder, making sure the lugs of the lid insert in the slots of the appliance. The lug should end up in front of the symbol located on the appliance. The brewing will start immediately after the grinding of the coffee. Therefore, make sure you proceed as indicated in the “MANUAL OPERATION” section, or the “PROGRAMMING THE COFFEE MAKER” section of this user manual. HINT: when the lid of the water tank and coffee grinder is left open, beeps will sound and “OPEN” will be displayed on the screen to remind you that the appliance cannot work with the lid open. We therefore advise you to fill the water tank and the coffee grinder before plugging in the appliance. MANUAL OPERATION • Slide the release / open button of the lid of the water tank and lift the lid open. Fill the water tank with cold water. The number of cups can be read on the graduated water tank. Close the lid. • Pull the filter holder out using its handle, fill the permanent filter with the desired quantity of ground coffee or use the grinder (see “USING THE COFFEE GRINDER” section). Then replace the filter holder in its initial position. NOTE: If you do not want to use the grinder and decide to fill the filter with normal ground coffee, press the GRIND OFF button, the orange pilot light will come on. NOTE: You cannot switch this “GRIND OFF” function on or off if the on/off light (Red), or the timer light (Green) are already lighted. • Make sure the jug is placed correctly on the hotplate. • To switch on your appliance, press once the ON/OFF switch. The red pilot light will come on and the coffee will start flowing after a few seconds. When you remove the jug from the appliance, a non-drip valve will automatically operate to stop any drops of coffee dripping onto the hotplate. Replacement of the jug automatically opens the non-drip valve and allows remaining coffee to filter trough into the jug. • Once the water tank is empty, we advise you to wait until the brewing process is finished and the filter has run empty before removing the jug. • You can switch off your appliance anytime simply by pressing the ON/OFF switch until all pilot lights are off. PROGRAMMING THE COFFEE MAKER Your coffee maker has a 24 hours timing, but the programmed clock remains in the memory as long as you do not modify it. • Check the time displayed on the clock. • Slide the release button of the lid of the water tank and lift it. Fill the water tank with cold water. The number of cups can be read on the graduated water tank. Close the lid. • Pull the filter holder out using its handle, fill the permanent filter with the desired quantity of ground coffee or use the grinder (see “USING THE COFFEE GRINDER” section). Then replace the filter holder in its initial position. NOTE: If you do not want to use the grinder and decide to fill the filter with normal ground coffee, press the GRIND OFF button, the orange pilot light will come on. NOTE: You cannot switch this “GRIND OFF” function on or off if the on/off light (Red), or the timer light (Green) are already lighted. • Press the PROG button twice successively. The time "12:00" and ‘TIMER" will be displayed on the electronic digital clock. • Set the desired programming time doing the same as described for the setting of the clock. • Once the setting is finished, wait about 15 seconds or press PROG key until “TIMER” disappears. The programming time will disappear and will be replaced by the time of the clock. • Make sure the jug is placed correctly on the hotplate. • Then press the ON/OFF switch twice successively and the green PROG pilot light will come on. The coffee machine is ready to start at the set time. • To check or to modify the programming time, press the PROG button twice until TIMER appears and it will be displayed. You can now modify it as you like. • When your appliance will start at the set time, the green pilot light will go out and the red ON/OFF pilot light will come on, indicating that the brewing process has started. • You can switch off your appliance anytime simply by pressing the ON/OFF switch until all pilot lights are off. When you remove the jug from the appliance, a non-drip valve will automatically operate to stop any drops of coffee dripping onto the hotplate. Replacement of the jug automatically opens the non-drip valve and allows remaining coffee to filter trough into the jug. Once the water tank is empty, we advise you to wait until the brewing process is finished and the filter has run empty before removing the jug. DESCALING AND CLEANING Descaling the coffee maker prolongs its life span. For decalcif...

Herunterladen

Geben Sie zwei Ziffern: