Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
3-2 DC/DC Converter ........................................................................................................ 3-2 FNB Interface ................................................................................................................. 3-3 CPU ................................................................................................................................. 3-3 Chapter 4 LANVIEW LEDs Chapter 5 Specifications Safety............................................................................................................................... 5-1 Service............................................................................................................................. 5-1 Physical........................................................................................................................... 5-2 Dimensions ............................................................................................................. 5-2 Weight...................................................................................................................... 5-2 Environment ........................................................................................................... 5-2 Appendix A FPIM Specifications FPIM-00 ......................................................................................................................... A-1 FPIM-02 and FPIM-04.................................................................................................. A-2 FPIM-05 ......................................................................................................................... A-3 v Chapter 1 Chapter 1 Introduction The 9F106-01 module, shown in Figure 1-1, is a two port FDDI router. One front panel network connection can be made to this module and routed to any other MMAC-Plus module via the FNB bus. Features Processor The 9F106-01 is equipped with an advanced IDT R4600 Fourth Generation 64 bit RISC microprocessor. This microprocessor provides a platform for all management functions within a scalable RISC-based architecture. System Management The 9F106-01 provides an interface to the System Management Bus (SMB-1) for intermodule management. Connectivity The 9F106-01 provides one dual attached FDDI interface using two standard Cabletron FPIMs. Routing The 9F106-01 provides Routing between the front panel interface and/or to any other module in the chassis via FNB -1 or FNB -2 of the FNB bus. IEEE 802.1d Spanning Tree Protocol is supported in all bridging functions. Introduction NOTE Management Information Base (MIB) Support The 9F106-01 module provides MIB support including the following: • IETF FDDI MIB • IETF MIB II For a complete list of supported MIBs, refer to the release notes provided in the module package. LANVIEW LEDs The 9F106-01 uses LANVIEW: the Cabletron Systems built-in visual diagnostic and status monitoring system. With LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance. Hot Swapping The 9F106-01 can be installed or removed from the chassis while the MMAC-Plus is powered up without affecting the operation of the remaining modules in the chassis. 1-3 Features Figure 1-1. The 9F106-01 Module FDDI FNB SMB CPU A UX C ON 9F106-01 0 B A FDDI 0 FPIM 1 FPIM 1 MMAC PLUS Introduction Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual. MMAC-Plus Installation Guide MMAC-Plus Operations Guide MMAC-Plus 9C300-1 Environmental Module User’s Guide MMAC-Plus 9C214-1 AC Power Supply User’s Guide Cisco Systems R4500 manuals - CRM-DOC or CRM-CDROM Getting Help If you need additional support with the MMAC-Plus, or if you have any questions, comments or suggestions concerning this manual, feel free to contact Cabletron Systems Technical Support: By phone: (603) 332-9400 By CompuServe®: GO CTRON from any ! prompt By Internet mail: support@ctron.com By mail: Cabletron Systems, Inc. P.O. Box 5005 Rochester, NH 03867-0505 Chapter 2 Chapter 2 Installing the MMAC-Plus Module The MMAC-Plus module may be installed into any of the 14 slots that are available. To install, follow the steps below: 1. Remove the blank panel, covering the slot that the module is being mounted in. All other slots must be covered, if modules are not being installed, to ensure proper airflow and cooling. 2. Carefully remove the module from the shipping box. (Save the box and packing materials in the event the module must be reshipped.) 3. Attach one end of the ESD wrist strap packaged with the MMAC-Plus chassis to your wrist. Plug the other end into the ESD Wrist Strap Grounding receptacle in the lower right corner of the MMAC-Plus Chassis shown in Figure 1. 4. Remove the module from the plastic bag. Observe all precautions to prevent damage from Electrostatic Discharge (ESD). 5. Carefully examine the module, checking for damage. If any damage exists, DO NOT install the module. Co...