Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: World Marketing of America Dateigröße: 3.2 mb Dateiname: Unterrichtssprache:

nTHERMOSTAT CONTROL OPERATIONnThe thermostatic control used on this model differs from standard thermostats. Standard thermostats simply turn on and off the burner. The thermostat used on this heater senses the room temperature. At times the room may exceed the set temperature. If so,the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set t o any comfort level between HI and LO. Note: The thermostat sensing bulb measures the temperature of air near the heater cabinet.This may not always agree with room temperatur(depending on housing construction, installation location, room size, open air temperatres,etc.) Frequent use of your heater will let you determine your own comfort levels. nTO TURN OFFnGAS TO APPLIANCE Shutting Off Heater 1. Turn control knob clockwise to the OFF position. 2. Turn off all electric power to the appliance if service is to be performed. Shutting Off Burner Only (pilot stays lit ) Turn control knob clockwise to the PILOT position. OPERATING YOUR HEATER THERMOSTAT MODEL KWN121 nFOR YOUR SAFETYnREADBEFORE LIGHTING A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. Figure 20 -Control Knob In The OFF Position Figure 21 -Pilot Figure 22 - Burner Partterns WHAT TO DO IF YOU SMELL GAS l Do not try to light any appliance. l Do not touch any electric switch, do not use any phone in your building. l Immediately call your gas supplier from a neighbor’s ph o n e. Fo llo w t h e g as supplier’s instructions. l If you cannot reach your gas supplier, call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it , call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. nLIGHTINGnINSTRUCTIONS 1. STOP! Read the safety information on the side of heater. 2. Make sure equipment shutoff valve is fully open. 3. Turn control knob clockwise to the OFF position. 4. Wait five(5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B”in the safety information on the side of heater. If you don’t smell gas, go to the next step. 5. Turn control knob counterclockwise to the PILOT position. Press in control knob for five(5) seconds. (see Figure 20). Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds. This will allow air to bleed from the gas system. lIf control knob does not pop up when released, contact a qualified service person or gas supplier for repairs. 6. With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the front of burner. If needed, keep pressing ignitor button until pilot lights. Note: If pilot does not stay lit, refer to Troubleshooting, pages 14 through 16. Also contact a qualified service person or gas supplier for repairs. Until repairs are m a d e , li g h t p il o t w ith match.To light pilot with match, see Manual Lighting Procedure. 7. Keep control knob pressed in for 30 seconds after lighting pilot.After 30 seconds, release control knob. l If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs. Note: If pilot goes out,repeat steps 3 through 7.This heater has a safety interlock system. W ait one(1) minute before lighting pilot again. 8. Turn control knob counter clockwise to desired seating level. The main burner should light. Set control knob to any heat level between HI and LO. (see Figure 22) CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve. nTHERMOSTAT CONTROL OPERATIONnThe thermostatic control used on this model differs from standard thermostats. Standard thermostats simply turn on and off the burner. The thermostat used on this heater senses the room temperature. At times the room may exceed the set temperature. If so,the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set t o any comfort level between HI and LO. Note: The thermostat sensing bulb measures the temperature of air near the heater cabinet.This may not always agree with room temperatur(depending...

Herunterladen

Geben Sie zwei Ziffern: