Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This odour is aodour when first used. This odour is aodour when first used. This odour is a normal condition caused by initial heat-normal condition caused by initial heat-normal condition caused by initial heat-normal condition caused by initial heat-normal condition caused by initial heat- ing ofing ofing ofing ofing of internal heainternal heainternal heainternal heainternal heater parter parter parter parter partststststs. T. T. T. T. Therherherherhereaf-eaf-eaf-eaf-eaf- terterterterter, any odour is normally the r, any odour is normally the r, any odour is normally the r, any odour is normally the r, any odour is normally the resultesultesultesultesult of household dust settling on theof household dust settling on theof household dust settling on theof household dust settling on theof household dust settling on the heater element.heater element.heater element.heater element.heater element. A - Main power on/off : Activates the power to the firelace from the remote control. B - Fire Log Accent Light: To illuminate the fireplace.(Can be used as a Nite Lite) C - Flame effect and speed: 1,2,3,4, off. D - Fan/Heater on/off: Turns the fan and heater on and off. E - Sound (optional) Batteries NOT included.Batteries NOT included.Batteries NOT included.Batteries NOT included.Batteries NOT included. Two AA batteries required.Two AA batteries required.Two AA batteries required.Two AA batteries required.Two AA batteries required. Note C D B E A 12345 6 MAINTENANCE Manual Controls BULB REPLACEMENT If you notice the flame look is darker on one side of the fireplace, check the light bulbs to ensure that one has not burned out. Bulb must be replaced with a MAX 60 watt incandescent clear light bulb. 1. Replace the bulb, turn the circuit breaker off or unplug the appliance. 2. Remove the front facia. 3. Detach the light access panel by removing the four screws. 4. Replace the burned out light bulb using a new 60 watt clear incandescent bulb. 5. Replace access panel and front facia. 6. Turn on the power or plug the appliance back in. 7. Turn on the main power and test. FIGURE 1 Light Access Panel Infrared Eye W415-0330 / B / 03.25.04 FINISHING FINISHING MANTEL Depending on the width of the mantel, it may be installed higher or lower from the top of the louvre opening. See drawing and chart below for proper installation height of your combustible mantel piece. Non-combustible mantels may be installed at any height above the appliance opening. When WhenWhenWhenWhenWhen using usingusingusingusingusing paint paintpaintpaintpaintpaint or ororororor lacquer lacquerlacquerlacquerlacquerlacquer to tototototo finish finishfinishfinishfinishfinish the thethethethethe mantel, mantel,mantel,mantel,mantel,mantel, such suchsuchsuchsuchsuch paint paintpaintpaintpaintpaint or ororororor lacquer lacquerlacquerlacquerlacquerlacquer must mustmustmustmustmust be bebebebebe heat heatheatheatheatheat resistant resistantresistantresistantresistantresistant to tototototo prevent preventpreventpreventpreventprevent discolouration. discolouration.discolouration.discolouration.discolouration.discolouration. W415-0330 / B / 03.25.04 Sides......................... 0 inches Back..........................0 inches Floor...........................0 inches Top............................0 inches FRAMING AND FINISHING CLEARANCE TO COMBUSTIBLES Set the control panel front edge flush with the finished wall surface. Nailing Tab Installation Sheet Metal Screw 1. Choose fireplace location. 2. Place fireplace in position. 3. Frame in fireplace with header across the top. It is important to allow for the finished facing materials when setting the depth of the frame. 4. Remove the two screws from the sides of the fireplace and attach the nailing tabs with the screws. 5. To determine the final location of the nailing tab, you must first determine the thickness of your finishing material (i.e. drywall) This will determine the dimension from the control panel front edge to the nailing tab. Secure with a sheet metal screw supplied. 6. Attach the nailing tabs to the frame. Corner Installation Top View Front View Note: In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the fireplace body, it is recommended that the walls of the fireplace enclosure be “finished” (ie: drywall/sheetrock), as you would finish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the cavity. HEARTH HEARTH A AAAAA hearth hearthhearthhearthhearthhearth is isisisisis NOT NOTNOTNOTNOTNOT necessary necessarynecessarynecessarynecessarynecessary but butbutbutbutbut is isisisisis recommended recommendedrecommendedrecommendedrecommendedrecommended for forforforforfor aes- aes-aes-aes-aes-aes- thetic thetictheticthetictheticthetic pur purpurpurpurpurposes posesposesposesposesposes. ..... The TheTheTheTheThe finished finishedfinishedfinishedfinishedfinished height heightheightheightheightheight of ofofofofof...