Stimmen - 6, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Vermont Casting Dateigröße: 4.03 mb Dateiname: Unterrichtssprache:

... Fig. 4 Corner installation, minimum corner clearances and flue centerline. Wall Centerline from Floor AA Effective Minimum Centerline 57” (1448 mm) (CFM Corporation Pipe) 55” (1399 mm) (Simpson DuraVent Pipe) ST131b Fig. 5 Minimum wall centerline. Direct Vent Only * needed for installing DuraVent Minimum Vent Kit #2792 or CFM Corporation Minimum Vent Kit #7TFSMSK. ACDBA: Rear Wall 4” (102 mm) B: Min. Clearance 44” (1118 mm)* C: Min. Alcove Height 72” (1830 mm)* D: Max. Alcove Depth 48” (1220 mm) Sidewall Clearance 6” (150 mm) ST101b Fig. 6 Dimensions and clearances to ceiling or alcove. Direct Vent Only Wall and Ceiling Clearances Hearth Requirements The Radiance Heater must be installed on rigid flooring. When the heater is installed directly on any combustible surface other than wood flooring, a metal or wood panel extending the full width and depth of the unit must be used as the hearth. There are no other hearth requirements. Radiance Direct Vent Gas Heater Gas Specifications Max. Input BTU/h Min. Input BTU/h Model Fuel Gas Control RADVT Series Nat Millivolt 38,000 25,000 RADVT Series Prop Millivolt 36,000 25,000 RADVTC Series Nat Comfort Control 38,000 25,000 RADVTC Series Prop Comfort Control 36,000 25,000 Weight: Fully assembled; 350 lbs. Gas Inlet and Manifold Pressures Inlet Minimum Natural LP (Propane) 5.5” w.c. 11.0” w.c. Inlet Maximum 14.0” w.c. 14.0” w.c. Manifold Pressure 3.5” w.c. 10” w.c. The installation of your Vermont Castings stove must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition, or CSA B149.1 Installation code. (EXCEPTION: Do not derate this appliance for altitude up to 2,000 (610 m) for natural gas and 4,500 feet (1,370 m) for LP Gas. Maintain the manifold pressure at 3.5” w.c. for Natural Gas and 10.0” w.c. for LP Gas. High Elevations Input ratings are shown in BTU per hour and are certified without deration for elevations up to 2,000 feet (610 m) for natural gas and 4,500 feet (1,370 m) for LP gas above sea level. In the USA installations with elevations above 2,000 feet (610 m) for natural gas and 4,500 feet (1,370 m) for LP gas must be in accordance with the current ANSI Z223.1/NFPA 54 and/or local codes having jurisdiction. In Canada, please consult provincial and/or local authorities having jurisdiction for installations at elevations above 2,000 feet (610 m) for natual gas and 4,500 feet (1,370 m) for LP gas. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or the gas supplier. Horizontal Termination The vent must rise vertically a minimum of 24” (610mm) off the top of the unit, before the first elbow. The horizontal run may extend up to 20’ (6m) and include a vertical rise of up to 40’ (12m). (Fig. 7) Horizontal termination must also meet the criteria shown in Figures 10 through 12. • Approved vent systems must terminate above and including the heavy line in Figure 7. • Two 45. elbows may be substituted for each single 90. elbow. • With a rise between 2’ - 5’, one 90. or two 45. elbows may be used. .................................................................................................................................. Vertical Run (in feet)(Measured from the appliance flue collar to the top of the vent pipe.) Horizontal Run (in feet) ................................................................................ ST134a May use up to three 90° Elbows One 90° Elbow Unacceptable Venting Configuration Fig. 7 Horizontal vent termination window. Radiance Direct Vent Gas Heater Vertical Termination Restrictor Plate Adjustment for Extended Pipe Runs A vertical vent system must terminate no less than 8’ (2.44 m) and no more than 40’ (12 m) above the appliance flue collar. A restrictor plate (supplied) must be used, where specified, in all vertically terminated vent systems. (Refer to Figure 8) NOTE: The restrictor plate supplied with the vertical termination should be discarded. Adjust the restrictor plate according to recommendations in Figure 10. A vertically terminated vent system must also conform to the following criteria: • No more than three 90° elbows may be used. • Two 45° elbows may be substituted for one 90. elbow. No more than six 45° elbows may be used. • Vent must rise a minimum of 2 feet (305 mm) before offset is used. • Termination height must conform to roof clearance The Radiance stove is shipped with a restrictor plate in the Parts Bag. Adjustments can be made by loosening the adjustment screw to allow the restrictor plate to slide up or down. (Fig. 9) A guide for usage is shown in Figure 10. NOTE: Some installations may require some adjustment by the installer for optimum flame appearance. Optimum flame appearance is a flame that is not subject...

Herunterladen

Geben Sie zwei Ziffern: