Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
See FIGURE 32. 3/8 X 1-3/4” 88 7 48 44 82 31 STEP 35: FIGURE 35 • Route the WEIGHT STACK CABLE (48) around one 4-1/2” PULLEY (43) and assemble the PULLEY to the BOOM BRACKET (8) using one 3/8 X 3-3/4” BOLT (93), two 3/8 X 1” SPACERS (57), and one 3/8” LOCK NUT (82). See FIGURE 35. 44 48 82 57 3/8 X 3-3/4” 93 8 • Screw the threaded end of the WEIGHT STACK CABLE (48) into the end of the FLOATING PULLEY BRACKET (16) . 16 STEP 36: FIGURE 36 • SECURELY assemble two 2” NYLON SPACERS (119) to the BOOM BRACKET (8) using two 3/8 X 2-3/4” BOLTS (90) and two 3/8” LOW HEIGHT LOCK NUTS (83) as shown in FIGURE 36. 119 90 3/8 X 2-3/4” 8 83 STEP 37: FIGURE 37 • Route the LAT CABLE (49) around one 3-1/2” PULLEY (44) and assemble two PULLEY PLATES (7) to the 3-1/2” PULLEY (44) using one 3/8 X 1-3/4” BOLT (88) and one 3/8” LOCK NUT (82). See FIGURE 37. 88 3/8 X 1-3/4” 7 44 82 • Route the LAT CABLE (49) around one 3-1/2” PULLEY (44) and assemble the PULLEY to the BOOM BRACKET (8) using one 3/8 X 3-3/4” BOLT (93), two 3/8 X 1” SPACERS (57), and one 3/8” LOCK NUT (82). See FIGURE 37. • Route the LAT CABLE (49) through the FRAME (1) and assemble one 3-1/2” PULLEY (44) to the FRAME (1) using one 3/8 X 3-3/4” BOLT (93), two 3/8 X 1-1/16” FLANGE SPACERS (56) and one 3/8” LOCK NUT (82). See FIGURE 37. 44 49 82 57 3/8 X 3-3/4” 93 93 3/8 X 3-3/4” 56 1 8 32 STEP 38: FIGURE 38 82 49 93 3/8 X 3-3/4” 118 8 33 • Securely assemble the LAT CABLE (49) to the THREADED HOUSING (118) then assemble the THREADED HOUSING (118) to the BOOM BRACKET (8) using one 3/8 X 3-3/4” BOLT (93), two 3/8 X 1” SPACERS (57) and one 3/8” LOCK NUT (82) as shown in FIGURE 38. STEP 39: FIGURE 39 82 11 3/8 X 3-3/4” 93 120 • SECURELY assemble two 3” NYLON SPACERS (120) to the BASE PLATES (11) using two 3/8 X 3-3/4” BOLTS (93) and two 3/8” LOCK NUTS (82) as shown in FIGURE 39. 57 8 STEP 40: 34 • Route the PRESS/LEG CABLE (47) under one 4-1/2” V-GROOVE PULLEY (45) and assemble the 4-1/2” V-GROOVE PULLEY (45) to the vertical bracket on the PRESS FRAME (32) using 3/8 X 2-3/4” BOLT (90) and one 3/8” LOW HEIGHT LOCK NUT (83). See FIGURE 40. STEP 41: • Route the PRESS/LEG CABLE (47) around one 3-1/2” PULLEY (44) and assemble to the horizontal bracket on the PRESS FRAME (32) using one 3/8 X 1-3/4” BOLT (88), one CABLE RETAINING CLIP (105) and one 3/8” LOCK NUT (82). See FIGURE 41. • Route the PRESS/LEG CABLE (47) around one 3-1/2” PULLEY (44) and assemble to the vertical bracket on the PRESS FRAME (32) using one 3/8 X 1-3/4” BOLT (88) and one 3/8” LOCK NUT (82). See FIGURE 40. • Securely assemble the PRESS/LEG CABLE (47) and one 3-1/2” PULLEY (44) to the PRESS FRAME (32) using one 3/8 X 3-3/4” BOLT (93), two 3/8” X 1-1/16” FLANGE SPACERS (56) and one 3/8” LOCKNUT (82). FIGURE 40 FIGURE 41 45 3/8 X 1-3/4” 88 3/8 X 3-3/4” 93 3/8 X 2-3/4” 90 47 32 3/8 X 1-3/4” 88 32 82 105 44 47 56 44 83 82 STEP 42: FIGURE 41 3/8 X 1-3/4” 88 3/8 X 2-1/2” 89 32 34 • Assemble two 1” SQ. GLIDES (68) to the PRESS FRAME (32) and two 1” SQ. GLIDES (68) to the inside of the PRESS ADJUST BRACKETS (37) at the point where the PRESS ADJUST BRACKETS come into contact with the PRESS FRAME (32) as shown in FIGURE 42. • Route the PRESS/LEG CABLE (47) around one 4-1/2” PULLEY (43) and assemble the 4-1/2” PULLEY (43) to the PRESS ADJUST BRACKETS (37) using one 3/8 X 1-3/4” BOLT (88) and one 3/8” LOW HEIGHT LOCK NUT (83). See FIGURE 42. • Assemble two PRESS ADJUST BRACKETS (37) to the INTERIOR PRESS ADJUST (34) using two 3/8 X 2-1/2” BOLTS (89) and two 3/8” LOW HEIGHT LOCK NUTS (83) as shown in FIGURE 42. 37 68 47 83 43 35 3/8 X 1-3/4” 88 44 82 47 9 STEP 43: FIGURE 43 • Route the PRESS/LEG CABLE (47) thru the tube and behind the GUIDE RODS on the BASE FRAME (9) as shown in FIGURE 43. Slide GUIDE RODS up just enough to get the cable end thru. Push GUIDE RODS down when finished. • Route the PRESS/LEG CABLE (47) around one 3-1/2” PULLEY (44) and assemble the 3-1/2” PULLEY (44) to the bracket on the BASE FRAME (9) using one 3/8 X 1-3/4” BOLT (88) and one 3/8” LOCK NUT (82). See FIGURE 43. 83 36 STEP 44: FIGURE 44 • Route the PRESS/LEG CABLE (47) around one 3-1/2” PULLEY (44) and assemble the 3-1/2” PULLEY (44) to the PULLEY PLATES (7) using one 3/8 X 1-3/4” BOLT (88) and one 3/8” LOCK NUT (82). See FIGURE 44. 88 3/8 X 1-3/4” 82 44 7 STEP 45: FIGURE 45 • Route the PRESS/LEG CABLE (47) around one 3-1/2” PULLEY (44) and assemble the 3-1/2” PULLEY (44) to the bracket on the REAR UPRIGHT (6) using one 3/8 X 1-3/4” BOLT (88) and one 3/8” LOCK NUT (82). See FIGURE 45. 3/8 X 1-3/4” 88 82 44 6 47 47 37 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 46 44 STEP 46: 83 22 3/8 X 6” 121 105 57 47 • Assemble two BOOM PULLEY PLATES (22), three 3-1/2” PULLEYS (44) and two CABLE RETAINING CLIPS (105) to the BASE PLATES (11) using one 3/8 X 6” BOLT (121), two 3/8 X 1” SPACERS (57) and one 3/8” LOW HEIGHT LOCK NUT (83). See FIGURE 46. (Note: Loop the PRESS/LEG CABLE (47) around the PULLEY prior to assembling the center PULLEY to the BASE PL...