Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Gas control knob not pressed in while in PILOT position 4. Air in gas lines when installed 5. Depleted gas supply (propane/LP models only) 6. Pilot is clogged 7. Gas regulator setting is not correct 1. Turn on gas supply or open equipment shutoff valve 2. Turn gas control knob to PILOT position 3. Press in gas control knob while in PILOT position 4. Continue holding down control knob. Repeat igniting operation until air is removed 5. Contact local propane/LP gas company 6. Clean pilot (see Cleaning and Maintenance, page 28) or replace pilot assembly 7. Replace gas control Pilot lights but flame goes out when control knob is released 1. Gas control knob not fully pressed in 2. Gas control knob not pressed in long 1. Press in gas control knob fully 2. After pilot lights, keep gas control knob enough pressed in 30 seconds 3. Equipment shutoff valve not fully open 3. Fully open equipment shutoff valve 4. Pilot flame not touching thermocouple, 4. A) Contact local natural or propane/LP which allows thermocouple to cool, gas company causing pilot flame to go out. This prob-B) Clean pilot (see Cleaning and lem could be caused by one or both of Maintenance, page 28) or replace pi- the following: lot assembly A) Low gas pressure B) Dirty or partially clogged pilot 5. Thermocouple connection loose at con5. Hand tighten until snug, then tighten trol valve 1/4 turn more 6. Thermocouple damaged 6. Replace pilot assembly 7. Control valve damaged 7. Replace control valve For more information, visit more information, visit 108661-01D 30 30 TROUBLESHOOTING TROUBLESHOOTING Continued OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Burner does not light after pilot is lit 1. Burner orifice clogged 1. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice 2. Inlet gas pressure is too low 2. Contact local propane/LP or natural gas company 3. Thermopile leads disconnected or im- 3. Reconnect leads properly connected 4. Thermopile is defective 4. Replace thermopile Delayed ignition burner 1. Manifold pressure is too low 1. Contact local propane/LP or natural gas company 2. Burner porting or orifice clogged 2. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice Burner backfiring during combustion 1. Burner orifice is clogged or damaged 1. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice 2. Damaged burner 2. Replace damaged burner 3. Gas regulator defective 3. Replace gas control Slight smoke or odor during initial operation 1. Residues from manufacturing processes 1. Problem will stop after a few hours of and logs curing operation Heater produces a whistling noise when 1. Turning gas control knob to HI position 1. Turn gas control knob to LO position and burner is lit when burner is cold let warm up for a minute 2. Air in gas line 2. Operate burner until air is removed from line. Have gas line checked by local pro- pane/LP or natural gas company 3. Dirty or partially clogged burner orifice 3. Clean burner (see Cleaning and Maintenance, page 28) or replace burner orifice Glass soots 1. Flame impingement on logs 1. Adjust the log set so that the flame does not excessively impinge on it 2. Debris around burner air mixer 2. Inspect the opening at the base of the burner to see that it is NOT packed with any type of material Fireplace produces a clicking/ticking noise just after burners are lit or shut off 1. Metal expanding while heating or contracting while cooling 1. This is common. If noise is excessive, contact qualified service person Remote does not function 1. Battery is not installed or battery power is low 1. Replace 9-volt batteries in receiver and remote control For more information, visit more information, visit 108661-01D TROUBLESHOOTING 31 TROUBLESHOOTING Continued WARNING: If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Fireplace produces unwanted odors 1. Gas leak. See Warning statement 1. Locate and correct all leaks (see Check- above ing Gas Connections, page 20) Fireplace shuts off in use 1. High or gusting winds 2. Low line pressure 3. Pilot is partially clogged 4. Inner vent pipe leaking exhaust gasses into system 5. Glass too loose and air tight gasket leaks in corners after usage 6. Bad thermopile or thermocouple 7. Improper vent cap installation 1. Fireplace has been tested for up to 40mph winds. However, extreme conditions may occur. See Lighting Instructions on page 25 2. Contact local propane/LP or natural gas company 3. Clean pilot (see Cleaning and Maintenance, page 28) 4. Locate and correct all leaks (see Checking Gas Connections, page 20) 5. Tighten glass ...