Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
If this face is replacing a Lopi Grill (96200801), make sure to replace the center deflectors. Hand-Rubbed Patina Finishes The optional patina finish is hand applied by a skilled artisan to permanently alter the metal colors and texture of the face. Each face is individually hand-polished and fired in an oven which imparts unique color subtleties with no two finishes alike. The patina finish on your face is a “living” color and will age and antique over time. Enjoy the timeless, rich luster of your beautiful new face._ Page 1 of 7 17601480 3/30/12 © Travis Industries, Inc. Bostonian (564) Wilmington Face Black 95400186 Nickel 95400187 Carbon Patina 95400194 Installation Details - 564 SS NOTE: This face has an adjustable bracket that allows for different facing depths to be tucked under the face. Page 2 of 7 17601480 3/30/12 © Travis Industries, Inc. Bostonian (564) Wilmington Face Black 95400186 Nickel 95400187 Carbon Patina 95400194 Installation - 564 SS 1 Remove the glass frame (see the owner's manual for details). Install glass frame cover as shown to the right. 2 Install face mounting brackets to the fireplace. Place the cover over the top of the door frame. to lock the cover in place. Page 3 of 7 17601480 3/30/12 © Travis Industries, Inc. Bostonian (564) Wilmington Face Black 95400186 Nickel 95400187 Carbon Patina 95400194 Installation - 564 SS (continued) 3 The facing and hearth (if applicable) must be installed prior to attaching the face. See the installation manual for complete details. Raised Fireplaces Page 4 of 7 17601480 3/30/12 © Travis Industries, Inc. Bostonian (564) Wilmington Face Black 95400186 Nickel 95400187 Carbon Patina 95400194 Installation - 564 SS (continued) 4 Install the face following the directions below. Attach the upper brackets to the face with the included nuts. The upper bracket consists of two pieces - note orientation. Optional Facing (and/or hearth) -See the installation manual for details. The face is secured to the fireplace with four screws. Two C J of the screws are fastened to the upper brackets with press nuts. The lower screws are included with the face. Slide the face into place. The tabs on the upper brackets insert into the slots on the fireplace brackets, holding the face in place while the screws are tightened. Plated Surfaces Use denatured alcohol and a soft cloth to clean plated surfaces. Marks left on the surface may damage the face. \ Soft Cloth A Denatured Alcohol Page 5 of 7 17601480 3/30/12 © Travis Industries, Inc. Bostonian (564) Wilmington Face Black 95400186 Nickel 95400187 Carbon Patina 95400194 Installation - 564 Electric 1 Install the upper heat shield onto the 564 E fireplace. Place the upper heat shield included with this kit on top of the fireplace (note position of heat shield). Place the stock heat shield on top of it Page 6 of 7 17601480 3/30/12 © Travis Industries, Inc. Bostonian (564) Wilmington Face Black 95400186 Nickel 95400187 Carbon Patina 95400194 2 Place the face, face down, on a soft, non-scratching surface. Install the 564 Electric mounting brackets onto the back of the face. Attach the 564 E side bracket. Use the nuts included with this kit. Repeat steps “a” through “c” for the opposite side. ©Before installing the face verify the lower grill is centered. Loosen the nuts and adjust if necessary. Attach the 564 E hinge bracket. Use the nuts removed earlier. 3 Pull the electric fireplace out of the mantel (or built-in location). Attach the cove cover and face following the directions below. Slide the fireplace back into place to complete the installation. Hang the 564 E cove cover over the glass -this keeps light from exiting the grill opening along the top of the face. Lift the face up slightly, tilt it forward and insert the top hooks until the face locks in place. Tilt the face back slightly and insert the bottom hooks into the slots on the fireplace Page 7 of 7 17601480 3/30/12 © Travis Industries, Inc....