Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Figure 13.14 Inside Fit Method (Tonic Decorative Front Only) 0 in. 0 in. 0 in. NON-COMBUSTIBLE BOARD Top Joint Side Joint Bottom Joint Non-Combustible Finishing Material 4 in. MINIMUM Non-Combustible Finishing Material 4 in. MINIMUM Figure 13.15 Noncombustible Surface Finishing Material 0-4 Inches Thick-Inside Fit Method (Tonic Decorative Front Only) Non-Combustible Finish Material 0-4 Inches Thick Bottom Joint 3/4 IN. 3/4 IN. Figure 13.16 Noncombustible Surface Finishing Material 0-4 Inch Thick-Inside Fit Method (Tonic Decorative Front Only) Heat & Glo • SLR • 2143-900 Rev. B • 7/08 D. Decorative Fronts WARNING! Risk of Fire! A decorative front is required for this model. DO NOT operate this appliance without a decorative front in place. Only doors certified for use with this appliance model may be used. Contact your dealer for a list of doors that may be used. TONIC DECORATIVE FRONT (TN-SLR-**) Inside and Overlap Fit See Section 13.C. Figure 13.17 Tonic Decorative Front MARTINI DECORATIVE FRONT (MT-SLR-**) Overlap Fit Only See Section 13.C. Figure 13.18 Martini Decorative Front The tinted glass on the Martini Decorative Front meets the tempered glass specifications in Section 1.B of this installation manual. Heat & Glo • SLR • 2143-900 Rev. B • 7/08 14 Appliance Setup 14 A. Remove Fixed Glass Assembly See Section 14F. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the firebox. The standard black rock media and manual bag assembly are also shipped underneath the firebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity. D. Accessories Install approved accessories per instructions included with accessories. Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories. WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty. Heat & Glo • SLR • 2143-900 Rev. B • 7/08 E. Rock Media Instructions CAUTION Sharp Edges • Wear protective gloves and safety glasses during installation. BURNER PORT SLOT MUST BE FREE OF ROCKS Cleaning the Rock During shipment of the Rock Media, dust and debris can accumulate. It is recommended that the Rock Media be rinsed thoroughly with water to remove dust and small glass particles. An easy method to clean the Rock Media is to dump the rocks into a bucket and rinse thoroughly with a garden hose. Allow the rocks to dry before installing them Figure 14.2. Place Rock Media WARNING! Risk of Fire. DO NOT place rock media di- NONO YES YES Figure 14.1. Selecting Flat Rocks for Pilot Cover. • WARNING Figure 14.3. Burner Tracks Delayed Ignition Risk • Place stones according to instructions. DO NOT PLACE ROCK MEDIADO NOT PLACE ROCK MEDIA BETWEEN BURNER TRACKSBETWEEN BURNER TRACKS • Do NOT place stones in area in front of pilot or between burner tracks. • Do NOT place stones in a position that they may fall into area in front of pilot. • Do NOT use any media other than the stones supplied with this fireplace. • Do NOT use more than one 10 lb. bag of rock media per fireplace. Fireplace will not function properly. Delayed ignition may occur. DO NOT PLACE ROCK MEDIADO NOT PLACE ROCK MEDIA IN FRONT OF PILOT ASSEMBLYIN FRONT OF PILOT ASSEMBLY • into the fireplace. INSTALLATION 1. Choose 7 - 10 flat, quarter-sized, pieces of Rock Media and set them aside. These will be used later to conceal the pilot cover. Reference Figure 14.1 for choosing flat pieces of glass. rectly in front of the pilot assembly or between the burner tracks over the burner ports.. 3. Figure 14.4 shows an outline of the area in front of the pilot assembly. No rock media may be placed in the outlined area. Continue to place an even amount of Rock Media over the entire base pan. DO NOT install Rock Media in between the tracks over the entire length of the burner. 2. Place an even layer of decorative rock around the base pan as shown in Figure 14.2. Do not place rocks in the slot over the burner ports. See Figures 14.2 and 14.3. This may cause lighting issues, undesirable burner flame, or delayed ignition. Figure 14.4. Pilot Bracket Detail Heat & Glo • SLR • 2143-900 Rev. B • 7/08 • 4. The rock media placement jig must remain in place while media is placed on the basepan and around the pilot bracket. 5. Remove the rock media placement jig by removing the screw as noted in Figure 14.5. SCREWSCREW Figure 14.5. Remove Screw 6. Place the flat pieces of Rock Media that were sorted out in Step 1, carefully hide the pilot cover. See Figures 14.6 and 14.4. • Figure 14.6. Place Flat Pieces of Rock Media Heat & Glo • SLR • 2143-900 Rev. B • 7/08 Heat & Glo • SLR • 2143-900 Rev. B • 7/08 57 H. Air Shutter Setting Air shutter settings may be adjusted by a qualifi ed installer at the time of installation. ...