Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Humminbird Dateigröße: 1.6 mb Dateiname: Unterrichtssprache:

5. While holding the control head in place, slide the bolt provided through the mounting bracket assembly, and screw the mounting knob onto the other side, in order to hold the control head in place. Hand tighten only! 6. You can tilt the control head by loosening the mounting knob and tilting the control head forward or backward to suit your needs. You can also swivel the control head on the mounting bracket by grasping the control head and rotating it. Positioning the Control Head Control Head Mounting Arms Bolt Mounting Bracket Mounting Knob Assembling the Mounting Arms Retainer Ring Mounting Bracket 4. Connecting the Cables to the Control Head Use this procedure to attach the transducer and power cables on the battery well to the keyed connectors on the back of the control head. 1. Attach the transducer and power cables from the battery well to the control head, using the keyed connectors on the back of the control head (see illustration). NOTE: The transducer and power cables are already permanently attached to the battery well. 5. Assembling and Attaching the Fishin’ Buddy® Mounting Bracket to the Boat Use this procedure to assemble the Fishin’ Buddy® mounting bracket, then attach it to the boat in the desired mounting location, either by using the C-clamp on the mounting bracket as a temporary mount, or by using the permanent mounting slots on the bottom of the mounting bracket to screw or bolt it to the boat. NOTE: C-clamp mounting is the most versatile and portable way to mount the Fishin. Buddy® to your boat. Connect the Cables to the Control Head Control Head Power Transducer The Fishin’ Buddy® should be mounted where it will be most visible and accessible. Use the following information when considering a mounting location: • The transducer will not work when it is not in the water. • Turbulent water or water filled with air bubbles can cause interference or prevent the transducer from operating. 1. Assemble the mounting bracket as shown below, using either one of the two ratcheted mounting posts provided (see illustration), and screw on the knob. Hand tighten only! Mounting Bracket (Vertical) Pivot adjustment knob Mounting Bracket (Horizontal) Pivot adjustment knob Permanent mounting slots C-clamp Permanent mounting slots C-clamp 6. Mounting the Fishin’ Buddy® Use this procedure to mount the Fishin’ Buddy®. NOTE: When mounted, the Fishin. Buddy® transducer must be positioned so that it will be submerged when the boat is in the water. 1. Slide the Fishin’ Buddy® shaft into the mounting bracket support arm ring. 2. You may need to adjust the mounting bracket support arm ring to keep the transducer on the bottom of the Fishin’ Buddy® pointing straight down. Loosen the pivot adjustment knob and make the necessary adjustments. 3. If the shaft is too long, or not long enough, adjust the length by removing the Fishin’ Buddy® from the mounting bracket, and unscrew the collar at the bottom of the shaft until it allows the shaft to telescope. Adjust the length of the shaft as needed, then tighten the screw collar once more. Re-mount the Fishin’ Buddy® to the mounting bracket. NOTE: Only the 130 and 140c Fishin. Buddy® units have adjustable mounting shafts. The 110 and 120 Fishin. Buddy® units have a fixed shaft length. Press the power button and start fishing! The Fishin’ Buddy® is designed to run automatically with just a press of the power button. To get the most out of your Fishin’ Buddy®, read the next section on functions and features. Powering ON and OFF Press and release the POWER-MENU key to power the Fishin’ Buddy® on. Press and hold the POWER-MENU key until the unit shuts down to power off. When the Fishin’ Buddy® powers on, the Start-Up menu temporarily appears. From this menu, select either Start-Up, Simulator, or SetUp. • Use Start-Up for on the water use. • Use Simulator for learning how to use the system with simulated sonar data; access Simulator by pressing the Right Arrow Key once. • Use SetUp to display additional set-up menu choices; access SetUp by pressing the Right Arrow Key twice (See SetUp Menu for more information). The Menu System A simple menu system allows you to access your Fishin’ Buddy® adjustable settings. To activate the menu system, press the POWER-MENU key. Press the POWER-MENU key repeatedly to display the Fishin’ Buddy® menu settings, one at a time. When a menu setting is on the display, use the RIGHT and LEFT Arrow keys to adjust the menu setting. Menu settings are saved and removed from the screen automatically after several seconds. In Normal operating mode, most menu settings saved to memory will not return to their default values when the unit is turned off. See individual menu choices for more information. NOTE: Each time the POWER-MENU key is pressed, the backlight momentarily illuminates for easy viewing at night. Adjust the LIGHT menu setting to keep the backlight on. NOTE: If Simulator Mode is selected from the Start-Up Menu and a transducer is plugged in, s...

Herunterladen

Geben Sie zwei Ziffern: