Make sure that the room in which the appliance is located is well ventilated during this operation. 24. It is not advisable for the appliance to be positioned where it is exposed to draughts which might prevent it from working properly. SAVE THESE INSTRUCTIONS HOW TO USE YOUR HEATER FEET ASSEMBLING Remove the feet from the packing. Fit the feet to the appliance as follows: 1 Insert the anchor pins (A) into the slots and turn the foot until it clicks into position (fig. 1). 2 Fasten the feet in p

1 EÈK. 1 Abb. 1 Kuva. 1 Рис 1 Rys. 1 1 . Sbrc Obr. 1 Sl. 1 Fig. З EÈK. 3 Abb. З Kuva. 3 Рис З Rys. 3 3. Sbrc Obr.3 Sl.3 Fig. 4 EÈK. 4 Abb. 4 Fig. 2 EÈK. 2 Abb. 2 Kuva. 2 Рис 2 Rys. 2 2. Sbrc Obr.2 Sl.2 [кУБ] Радиатор отопления - универсальный прибор для нагрева жилого помещения с тремя уровнями мощности. Кроме того, прибор оснащен уникальной функцией, которая обеспечитвает наилучший комфорт в любых условиях. Для максимального использования возможностей прибора рекомендуем прочесть до кон

18. Be sure that the plug is fully inserted into an appropriate receptacle. Please remember that receptacles also deteriorate due to aging and continuous use: check periodically if signs overheating or deformations are evidenced by the plug. Do not use the receptacle and CALL your electrician. 19. Check that neither the appliance nor the power cable have been damaged in any way during transportation. 20. CAUTION: to prevent electric shock match wide blade of plug to wide slot, fully insert. 21.

To get the very best out of your new convector it is advisable to read these instructions before using it. This will ensure that you gain optimum results and use the convector safely. Assembling the feet Fit the feet to the convector as follows: -Insert the foot ensuring that the bigger hole A on the foot coincides with the screw mounted on the base of the convector (see figure 1); then screw in the remaining three screws (see figure 2) which are supplied. Note: the convector must be used only w

Programming the Electronic Timer The timer allows you to set two programs in a 24h period. To program the timer: Press the “Timer button A, this accesses the program, the following is displayed: -The flashing message “--:--“; -The message “ON” at the bottom left (ON time setting); -The symbol “A” at the right indicating that the first program controlling is being set; To setting the starting time press “hour button” to set the hour and “min button” to set the minutes, then confirm the ON time by

N.B.This function is not guaranteed in the event of power failures, lasting more than 2 minutes. Programming the Electronic Timer The timer allows you to set two programs in a 24h period. To program the timer: Press the “Timer button A, this accesses the program, the following is displayed: -The flashing message “--:--“; -The message “ON” at the bottom left (ON time setting); -The symbol “A” at the right indicating that the first program controlling is being set; To setting the starting time pre

3. This heater becomes very hot when operating. To avoid burns, do not touch its hot surfaceswith your bare skin. Use the heater’s handle when moving it. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (90 cm) awayfrom the heater’s front and top, and also well away from its sides and rear. 4. Extreme caution should be taken when leaving an operating heater unattended near childrenor handicapped persons. 5. Always unplug the heater whe

SAVE THESE INSTRUCTIONS 2 3 FITTING THE WHEELS Remove the feet with the bracket wheels from the polystyrene packing. Turn the radiator upside-down and rest on the polystyrene. Fit the wheels to the spindles on the feet and push firmly until they click into position. Pull each wheel to check that it is correctly inserted. The feet with the casters must be fitted with two arc-shaped brackets only between the 1st and 2nd element and the penultimate (see fig. 1 to 3 inclusive). HOW TO USE YOUR HEATE