Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Jet Tools Dateigröße: 315.8 kb Dateiname: Unterrichtssprache:

IMPORTANT: Do not oil filters. Pump Pressure Adjustment 1. Remove pressure gauge plug from filter end cover. 2. Install accessory pressure gauge (part number HA1180). 3. Start heater (see Operation, page 7). Allow motor to reach full speed. 4. Adjust pressure. Turn relief valve to right to increase pressure. Turn relief valve to left to decrease pressure. See specifications at right for correct pressure for each model. 5. Remove pressure gauge. Replace pressure gauge plug in filter end cover. Air Intake Filter Lint Filter Air Output Filter Filter End Cover Fan Guard (100,000 BTU/Hr Model Shown) Figure 11 - Air Output, Air Intake, and Lint Filters (150,000 BTU/Hr Model Shown) Relief Valve Pressure Gauge Plug 125 PRESSURE ADJUSTMENT Plug Figure 12 - Pressure Gauge Plug Removal Pump Model Pressure 100,000 BTU/Hr 4.0 PSI 150,000 BTU/Hr 5.0 PSI Gauge 125 PRESSURE ADJUSTMENT Pressure Figure 13 - Adjusting Pump Pressure 13 Spark Plug Combustion Chamber Burner Head Air Line Hose Fuel Line Hose Screw Spark Plug Wire Spark Plug Combustion Chamber Burner Head Air Line Hose Fuel Line Hose Screw Spark Plug Wire Nozzle Burner Head Air line Fitting Fuel line Fitting Nozzle Seal 14 Chamber Burner Head Spark Plug Wire Air Line Hose Fuel Tube Flare Nut Spark Plug Screw Chamber Burner Head Spark Plug Wire Air Line Hose Fuel Tube Flare Nut Spark Plug Screw Nozzle Burner Head Nozzle Seal 15 Pump Rotor (Procedure if rotor is binding) 1. Remove upper shell (see page 10). 2. Remove filter end cover screws using 5/16" nut- driver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nut- driver. 5. Remove pump plate. 6. Remove rotor, insert, and blades. 7. Check for debris in pump. If debris is found, blow out with compressed air. 8. Install insert and rotor. 9. Check gap on rotor. Adjust to .003"/.004" (.076/.101mm) if needed (see Figure 19). Note: Rotate rotor one full turn to insure the gap is .003"/.004" (.076/.101mm) at tightest position. Adjust if needed. 10. Install blades, pump plate, air filters, and filter end cover. 11. Replace fan guard and upper shell. 12. Adjust pump pressure (see page 13). Note:If rotor is still binding, proceed as follows. 13. Perform steps 1 thru 6 above. 14. Place fine grade sandpaper (600 grit) on flat surface. Sand rotor lightly in “figure 8” motion four times (see Figure 20). 15. Reinstall insert and rotor. 16. Perform steps 10 thru 12 above. 150 ROTOR PFA/P 059 Blade Filter End Cover Air Intake Filter Pump Plate Air Output Filter Insert Rotor Fan Guard (100,000 BTU/Hr Model Shown) Figure 18 - Rotor Location Gap Adjusting Screw .003"/.004" (.076/.101mm) Gap Measured With Feeler Gauge Sandpaper Blade Rotor Gap Adjusting Screw Figure 19 - Gap Adjusting Screw Locations Figure 20 - Sanding Rotor 16 Setscrew Motor Shaft Setscrew Motor Shaft Fan Setscrew Motor Shaft 17 WIRING DIAGRAM SPECIFICATIONS ACCESSORY Purchase this accessory from your local dealer. Red White RedRed White Blue Green/Yellow Black Relay Motor Terminal Board Ignitor Brown Spark Plug 120V 60Hz Output Rating (BTU/Hr) Fuel Fuel Tank Capacity (U.S. Gal./Liters) Fuel Consumption (Gal. Per Hr./Liters Per Hr.) Electric Requirements Amperage (Normal Run) Hot Air Output (CFM/CMM) RPM 100,000 150,000 Use Only Kerosene or No. 1 Fuel Oil 9/34 .74/2.8 120 volt/60 hertz 4.5 480/13.6 3450 13.5/51 1.10/4.16 120 volt/60 hertz 4.5 648/18.3 3450 AIR GAUGE KIT - HA1180 Special tool to check pump pressure. 18 WHEELS AND HANDLES FOR 100,000 AND 150,000 BTU/Hr MODELS KEY NO. PART NUMBER PART DESCRIPTION 100,000 QTY. 150,000 QTY. 1 2 3 4 5 6 7 HA2203 HA2205 M12345-33 M12342-3 M12831-3 NTC-3C 097896-03 M28526 M51015-01 M16801-2 Handles Handles Screw, #10-24 x 1 3/4" Wheel Support Frame Wheel Support Frame Nut Torque, #10-24 Wheel Cap Nut Axle Axle 2 — 8 1 — 8 2 2 1 — — 2 8 — 1 8 2 2 — 1 1 2 3 45 6 7 ASSEMBLY, EURO PFA/PV 018A 19 20 MOTOR & PUMP 100 EAI/EBI PFA/P 010 ILLUSTRATED PARTS BREAKDOWN 100,000 BTU/Hr Model 13-1 13-2 13-3 13-4 13-5 13-6 13-7 13-8 13-9 13-10 13-11 13-12 13-13 13-15 13-16 13-17 13-18 13-14 Motor and Pump Assembly BURNER HEAD 100 EAI/EBI PFA/P 022 8-2 8-6 8-5 8-4 8-3 8-1 Burner Head Assembly 8-7 1 2 3 8 10 9 11 12 13 14 16 15 17 19 20 25 27 28 29 30 31 32 33 34 35 36 37 40 38 26 6 21 22 23 24 7 4 5 18 39 This list contains replaceable parts used in your heater. When ordering parts, PARTS LIST be sure to provide the correct model and serial numbers (from the model plate), 100,000 BTU/Hr Model then the part number and description of the desired part. KEY NO. PART NUMBER PART DESCRIPTION QTY. KEY NO. PART NUMBER PART DESCRIPTION QTY. 1 2 3 4 5 6 7 88-1 8-2 8-3 8-4 8-5 8-6 8-7 9 10 11 12 1313-1 13-2 13-3 13-4 13-5 13-6 13-7 13-8 13-9 13-10 13-11 13-12 13-13 13-14 13-15 13-16 098511-30 M15823-27 098512-07 078918-01 099213-01 M27417 HA2210 ** M51120-01 M10659-1 M10809-1 M8882 M50924-03 M50820-02 M10962-2 M11084-27 M50814-03 M51345-01 M51153-01 ** 079505-02 079975-01 FHPF3-2C M22009 M22456-1 M50545 M12179 M1654...

Herunterladen

Geben Sie zwei Ziffern: