Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Cadet Dateigröße: 3.48 mb Dateiname: Unterrichtssprache:

If the millivolt reading is less than 15 millivolt, replace the thermocouple. b. Defective valve. —If thermocouple is producing more than 15 millivolts, replace faulty valve. 3. Pilotburning,nogastoburner,valveknob“ON”,REMOTE/ OFF/ON switch “ON.” a. REMOTE/OFF/ON switch, wall switch, remote control or wires defective. —Check REMOTE/OFF/ON switch and wires for proper connections. Place jumper wires across terminal at switch. If burner comes on, replace defective switch. If OK, place jumper wires across switch wires at gas valve-if burner comes on, wires are faulty or connections are bad. b. Thermopile may not be generating sufficient millivolts. —If the pilot flame is not close enough physically to the thermopile, adjust the pilot flame. —Be sure the wire connections from the thermopile at the gas valve terminals are tight and the thermopile is fully inserted into the pilot bracket. —Check the thermopile with a millivolt meter. Take the reading at TH-TP& TPterminals of the gas valve. The meter shouldread350millivoltsminimum,whileholdingthevalve knob depressed in the PILOT position, with the pilot lit, and the REMOTE/OFF/ON switch in the OFF position. Replace the faulty thermopile if the reading is below the specified minimum. —WiththepilotintheONposition,disconnectthethermopile leads from the valve. Take a reading at the thermopile leads. The reading should be 350 millivolts minimum. Replace the thermopile if the reading is below the minimum. c. Defective valve. —Turn valve knob to ON. Place REMOTE/OFF/ON switch to ON. Check with millivolt meter at thermopile terminals. Millivolt meter should read greater than 200 millivolts. If the reading is okay and the main burner does not ignite, replace the gas valve. d. Plugged main burner orifice. —Check main burner orifice for blockage and remove. 4. Frequent pilot outage problem. a. Pilot flame may be too high or too low, or blowing (high), causing pilot safety to drop out. —Cleanandadjustflameformaximumflameimpingementon the thermocouple. Follow lighting instructions carefully. 5. The pilot and main burner extinguish while in operation. a. No LP (Propane) in tank. Check LP (Propane) tank. Refill fuel tank. b. Inner vent pipe leaking exhaust gases back into system —Check for leaks. c. Glass too loose, gasket leaks in corners after usage. —Be certain glass assembly is installed correctly. d. Horizontal vent improperly pitched. —The horizontal vent cap should slope down only enough to prevent any water from entering the unit. The maximum downwards slope is 1/4 inch. e. Bad thermopile or thermocouple. —Replace if necessary. f. Improper vent cap installation. —Check for proper installation and freedom from debris or blockage. 6. Glass soots. a. Flame impingement on logs. —Check and adjust log position. Contact Empire Comfort Systems, Inc. b. Debris around throat of main burner. —Inspect the opening at the base of the main burner. It is imperative that NO material be placed in this opening. 7. Flame burns blue and lifts off main burner. a. Insufficient oxygen being supplied. —Check to make sure vent cap is installed properly and free of debris. Make sure that vent system joints are tight and have no leaks. —Check to make sure that no material has been placed at the main burner base. Page 42 23552-4-0408 23552-4-0408 Page 43 DIRECT IGNITION WIRING DIAGRAM LED LIGHT LED LUMIERE BLACK NOIR GREEN VERT WHITE BLANC RED ROUGE BLACK NOIR GAS VALVE (OPTIONAL) WALL SWITCH VALVE DE GAZ INTERRUPTEUR MURAL (FACULTATIVE) 120 VAC LINE 120 VAC RTN JUNCTION BOX JONCTION BOITE SPARK IGNITOR ETINCELLE ALLUMER (OPTIONAL) REMOTE CONTROL RECEIVER 120V (FACULATIVE) CONTROLE E DISTANCE DU RECEPTEUR MAIN VALVE RETURN 1 12 13 GROUND 2 120V AC RETURN 4 120V AC HOT 6 MAIN VALVE HOT 8 CONTROL MODULE AUTORITE MODULE OR THERMOSTAT LED CODES Steady ON Normal operation, power ON to control 2 Flashes 3 unsuccessful ignition trials 3 Flashes Main burner flame failed 4 times during a single heating cycle 4 Flashes Interrupt power for 5 seconds to reset control Steady Flash Flame detected out of sequence OPTIONAL REMOTE CONTROL Electric (120 volt) Operated Remote Control (FREC) 1. Disconnect 3-prong power cord from receptacle. 2. Remove wire from 120 VAC hot terminal on control module. 3. Connect female terminal from receiver onto 120 VAC hot terminal on control module. 4. Connect remaining wire from remote control (male terminal) to (female terminal) on power cord removed from control module (step 2). Figure 61 5. Insert electric remote control power cord plug into the junction box on the right side of fireplace. 6. Connect 3-prong plug into receptacle. See wiring diagram on page 53. Page 44 23552-4-0408 A. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance • Do not touch any electrical switch • Do not use any phone in your building...

Herunterladen

Geben Sie zwei Ziffern: