Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Quadra-Fire Dateigröße: 3.18 mb Dateiname: Unterrichtssprache:

Remove Shipping Materials Remove shipping materials from inside or underneath the firebox. B. Leg Leveling System Figure 8.1 Thread Allen bolts through nuts until flush. The Allen bolts and nuts are included in the component pack inside the appliance firebox. Figure 8.2 Slide assembled nuts and bolts into the slots on the legs with the nuts on the bottom. Figure 8.3 Use a 5/32 in. 4mm) Allen wrench to adjust legs up and down to desired level. C. Flue Restrictor Installation When your installation falls within a shaded area on the vent graph (page 11) a flue restrictor must be installed for proper operation. Figure 8.4 Installation of the flue restrictor requires the removal of the baffle located inside the firebox. Remove the baffle by first removing the two screws holding the baffle in place (one on each side). Lift the baffle out of the bracket along the back of the firebox, angle the baffle slightly and remove it from the firebox. Figure 8.5 With the baffle removed, remove the two screws located in the back of the firebox. Reuse the screws to install the flue restrictor. September 1, 2008 Quadra-Fire · Garnet-T · 7016-127F Page 31 D. Accessories Install approved accessories per instructions included with accessories. Refer to Section 12 for appropriate accessories. WARNING Shock or fire risk. Use ONLY optional accessories approved for this appliance. • Using non-listed accessories voids warranty. • Using non-listed accessories may result in a safety hazard. • Only Hearth & Home Technologies approved accessories may be used safely. E. Positioning the Logs While still breakable, the logs do not become fragile until after the appliance is burned and they have cured. After curing, any handling must be done with care as breakage can easily occur. PLEASE NOTE: Logs have been designed to work specifically with the burner of this appliance. Exact placement will ensure proper operation of your gas appliance and reduce sooting. The three piece log set is packed in the components box and consists of the following: Qty Name Diagram 1 Rear Log Fig. 1 1 Left Log Fig. 2 1 Right Log Fig. 3 Figure 8.7 Align left front log with notch in burner and notch on rear log. Figure 8.8 Align right front log with burner and notch in left front log. F. Mineral Wool WARNING Explosion Risk. • Follow ember placement instructions in manual. • Do NOT place embers directly over burner ports. • Replace ember material annually. Improperly placed embers interferes with proper burner operation. Figure 8.6 Gently remove top of unit and set aside. Remove cast face by sliding straight up and set aside. Remove the glass by releasing the latch located on the top of the appliance. Lean glass frame forward and lift out. Place the notch in the Rear Log over the pilot assembly. Push the log all the way to the rear of the firebox. Figure 8.9 Place individual pieces of embers in front of and around the gas log where they can be seen. Space them so that gas can contact them on all sides. Avoid stacking the embers on top of each other. NOTE: Do not block gas ports. Page 32 Quadra-Fire · Garnet-T · 7016-127F September 1, 2008 G. Glass Replacement Turn the appliance OFF and let it cool down before replacing the glass. Lift off the appliance top and place it on a flat surface, with the porcelain side up, to prevent damage. Remove the appliance front by sliding it upward in the grooves, being careful not to chip the porcelain. Lay the front face up on a flat surface. Unhook latch now exposed on top of the appliance. Pull the top of the glass frame towards you and lift it out of the retainer along the bottom of the firebox. Replacement is the reverse of the removal. CAUTION Handle glass assembly with care. • Inspect the gasket to ensure it is undamaged. • Inspect the glass for cracks, chips or scratches. • Do NOT strike, slam or scratch glass. • Do NOT operate appliance with glass door removed, cracked, broken or scratched. • Replace glass assembly as a complete assembly. H. Blower Installation TOOLS REQUIRED: Short #2 Philips head screwdriver; 11/16" wrench; and a 3/8” wrench. FROM THE KIT YOU WILL NEED: Blower in mounting with wiring harness; speed control (rheostat); speed control knob; pal nut; snap disc; screws; and 1 zip-tie. FROM THE APPLIANCE COMPONENT BAG YOU WILL NEED: Snap disc bracket; 10-32 nut. KIT CONTENTS: 1 - Blower Mounted in Housing 2 - Speed Control Knob 3 - Pal Nut 4 - Ceramic Snap Disc 5 - Speed Control (Rheostat) 6 - Wire Harness (attached to Blower) 7 - 12 Screws 8 - 12 inch Glass Tape 9 - 1 Zip Tie 10 - Bracket #1 11 - Snap Disc Bracket 1110 Figure 8.10 Open and inspect contents of the blower kit. The contents of the kit are listed at left. If any of the parts are missing or damaged, please contact your dealer for replace- ments. NOTE: Not all parts will be used for this installation. Figure 8.11 Remove the top of the appliance and set aside. Remove the back shield by removing the two screws along the top of the shield. Place the blowe...

Herunterladen

Geben Sie zwei Ziffern: