Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Procom Dateigröße: 1.34 mb Dateiname: Unterrichtssprache:

The pilot is attached to the front of burner. If needed, keep pressing ignitor button until pilot lights. Note: If pilot does not stay lit, refer to Troubleshooting, pages 14 through 16. Also contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match.To light pilot with match, see Manual Lighting Procedure. 7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs. Note: If pilot goes out,repeat steps 3 through 7.This heater has a safety interlock system. Wait one(1) minute before lighting pilot again. 8. Turn control knob counter clockwise to desired seating level. The main burner should light. Set control knob to any heat level between HI and LO. (see Figure 23) CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve. Figure 21 - Control Knob In The OFF Position Figure 22 - Pilot Figure 23 - Burner Partterns THERMOSTAT CONTROL OPERATION. The thermostatic control used on this model differs from standard thermostats. Standard thermostats simply turn on and off the burner. The thermostat used on this heater senses the room temperature. At times the room may exceed the set temperature. If so,the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set to any comfort level between HI and LO. Note: The thermostat sensing bulb measures the temperature of air near the heater cabinet.This may not always agree with room temperature(depending on housing construction, installation location, room size, open air temperatures,etc.) Frequent use of your heater will let you determine your own comfort levels. TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Turn control knob clockwise to the OFF position. 2. Turn off all electric power to the appliance if service is to be performed. Shutting Off Burner Only (pilot stays lit ) Turn control knob clockwise to the PILOT position. 12 OPERATING HEATER Continued MANUAL LIGHTING. PROCEDURE 1. Remove lower front panel (see Figure 7 page 7). 2. Follow steps through 5 under Lighting Instructions on page12. 3. With control knob pressed in, strike match. Hold match to pilot until pilot lights. 4. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.Follow step 8 under Lighting Instuctions on page 12. 5. Replace lower front panel. INSPECTING BURNER Check pilot flame pattern and burner flame pattern often. PILOT FLAME PATTERN Figure 24 shows a correct pilot flame pattern. Figure 25 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down. If pilot flame pattern is incorrect, as shown in Figure 25. turn heater off (see To Turn Off Gas to Appliance. page 11,12 . see Troubleshooting. pages 14 through 16. Figure 24 - Correct Pilot Flame Pattern Figure 25 - Incorrect Pilot Flame Pattern BURNER FLAME PATTERN Figure 26 shows a correct burner flame pattern. Figure 26 shows an incorrect burner flame pattern. If burner flame pattern is incorect, as shown in Figure 27 . turn heater off (see To Turn Off Gas to Appliance pages 11&12) . see Troubleshooting (pages 14 through 16) Figure 26 - Correct Burner Flame Pattern Figure 27 - Incorrect Burner Flame Pattern CLEANING AND MAINTENANCE WARNING: turn off heater and let cool before cleaning. CAUTION: you must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc. ODS/PILOT AND BURNER . Use a vacuum cleaner, pressurized air, or a small, soft bristled brush to clean. CLEANING BURNER PILOT AIR INLET HOLE We recommend that you clean the unit every 2,500 hours of operation or every three months. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSl. Your local computer store, hardware store. or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can, you could damage the pilot assembly. 1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes. 2. Inspect burner, and pilot for dust and dirt. 3. Blow air through the ports/slots and holes in the bumer. Also clean the pilot assembly. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches...

Herunterladen

Geben Sie zwei Ziffern: