Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Procom Dateigröße: 1.34 mb Dateiname: Unterrichtssprache:

IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent. *A CSA/AGA design-certified WARNING: Never install equipment shutoff valve with 1/8" the heater NPT tap is an acceptable in a bathroom(Models alternative to test gauge connection. ML100HPA and ML100TPA , Purchase the optional CSA/AGA only ML060HPA is allowed in a design certified equipment bathroom. Check local codes.) shutoff valve from your in a recreational vehicle. dealer. See Accessories, page 17. where curtains, furniture. as a fireplace insert. LOCATING HEATER in high traffic areas. in windy or drafty areas. This heater is designed to be mounted on a wall. For convenience and efficiency, When the heater is installed in install heater Bathrooms,do not use flammable where there is easy access forproducts such as aerosol hair spray, operation, inspection, and service foot spary or any product that contains in coldest part of room flammable vapors and keep towels away from heater.(only ML060HPA is allowed in a bathroom.) CAUTION: If you install the heater in a home garage heater pilot and burner must CAUTION: This heater cre be at least 18 inches above ates warm air currents. These floor. currents move heat to wall sur locate heater where moving faces next to heater. Installing vehicle will not hit it. heater next to vinyl or cloth wall coverings or operating heater where impurities (such as tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist may discolor walls. 6 WARNING: Maintain the minimum clearances shown in Figure 4. If you can, provide greater clearances from floor, ceiling, and joining wall. Figure 4 -Mounting clearances As Viewed From Front of Heater FASTENING HEATER TO WALL Mounting Bracket The mounting bracket is located on back panel of heater (see Figure 5). It has been taped there for shipping. remove mounting bracket from back panel. Figure 5 -Mounting Bracket Location INSTALLATION Removing Lower Front Panel Of Heater 1. Remove two Screws near bottom corners of lower front panel. 2. Pull bottom of lower front panel forward, then down (see Figure 6). Figure 6 - Removing Lower Front Panel Of Heater Methods For Attaching Mounting Bracket To Wall Only use last hole on each end of mounting bracket to attach bracket to wall. Attach mounting bracket to wall only in one of two ways: 1. Attaching to wall stud 2. Attaching to wall anchor Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs. Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry). Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket. Marking Screw Locations 1. Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level. WARNING: Maintain minimum clearances shown in Figure 8. If you can, provide greater clearances from floor and joining wall. 2. Mark screw locations on wall. (see Figure 7) Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only. 3. Remove tape and mounting bracket from wall. Figure 7 - Mounting Bracket Clearances 7 Attaching Mounting Bracket To Wall Note: Wall anchors, mounting screws, and spacers are in hardware package. The hardware package is provided with heater. Attaching to Wall Stud Method For attaching mounting bracket to wall studs 1. Drill holes at marked locations using 9/64" drill bit. 2. Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall. 3. Insert mounting screws through bracket and into wall studs. 4. Tighten screws until mounting bracket is firmly fastened to wall studs. Attaching to Wall Anchor Method For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry) 1. Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep. 2. Fold wall anchor as shown in Figure 8 below. Figure 8 - Folding Anchor 3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall. 4. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to "pop" open anchor wings (see Figure 9). INSTALLATION Figure 9 - Popping Open Anchor Wing For Thin Walls 5. Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors. 6. Insert mounting screws through bracket and into wall anchors. 7. Tighten screws until mounting bracket is firmly fastened to wall. IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings. Placing Heater On Mounting Bracket 1. Locate two horizontal slots on back panel of heater (see Figure 10). 2. Place hea...

Herunterladen

Geben Sie zwei Ziffern: