Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Gas-Fired Products Dateigröße: 1.33 mb Dateiname: Unterrichtssprache:

BODY SECTION 6” fifi’ (sm 6” t Reflector 1 i Side view 6: Tube Support/Hanger Bracket (QTY-2; 13” r Emitter Tube 10 FT. BODY SECTION Tube Support/Hanger Bracket (QTY-2) T Emitter Tube CONTROL BOX 3/8’ Connector Burner Sight Glass 1/2’ MPT Gas Pipe Connection 8-1/2” Square Access Panel Clearances to Combustibles Label 120’ t (10 ft) 108” r Reflector _ Side View 1 6” Lighting & Shutdown Instructions Opening for Electrical Connection DRAFT INDUCER Flue Restrictor Plate 3/8” Connector EXHAUST HOOD - Required for UNVENTED use - T 13’ 11” I 4’x6” Starting Collar* * 4’ Starting Collar for LTS40-75 u -6- Form #43155010 Feb-04 10) LTS 40-175 - TYPICAL LAYOUTS Si I ww Ml « III II SYSTEM III II |L=—| — Ill) I ». lïï II SYSTEM | | 1— 1 ill ll - Ill II !'” 1 111 ii s«™ ||W%-% p- 1 mi ii in ii SYSTEM I I I“- 1 1,1 i I l il SYSTEM ■ I ■ ■ ■ 1 Lri'-t i ' El Straight El L Shape El U Shape El ZShaoe LEGEND u Control Unit • Draft Inducer Unit ■■■ 10 Ft. Body Section m 5 Ft. Body Section \ 90* Elbow MODEL EMITTER LENGTH Min. Max. LTS 40 15 Ft. 20 Ft. LTS 50 15 Ft. 30 Ft. LTS 60 20 Ft. 30 Ft. LTS 75 20 Ft. 30 Ft. LTS 80 30 Ft. 40 Ft. LTS 90 30 Ft. 40 Ft. LTS100 30 Ft. 40 Ft. LTS110 30 Ft. 40 Ft. LTS120 30 Ft. 40 Ft. LTS125 30 Ft. 50 Ft. LTS130 30 Ft. 50 Ft. LTS140 40 Ft. 50 Ft. LTS150 40 Ft. 50 Ft. LTS160 40 Ft. 50 Ft. LTS175 40 Ft. 50 Ft. NOTES: 1) The control unit must be connected directly to a 10 ft. aluminized steel body section in all configurations. 2) Joining of two 90° elbows directly together to form a "Z" shape is NOT permitted. 3) Any configuration of components not shown in the illustrations may be used except as noted in 1 and 2 above. 11) LTS 40-175 - HEATER ASSEMBLY/JOINING OF BODY SECTIONS_ During field assembly of the LTS series heater body sections, the recommended procedure is as follows: 1. Before hanging heater sections, first determine the actual layout of the system (see Section 10 for details). Consideration must also be taken for flue pipe, fresh air ducting, gas piping, etc., before hanging the heater. Typical suspension methods are shown in Section 17. DO NOT relocate the tube support/hanger brackets, especially at the control end of the heater. 2. Hang each heater body section individually. DO NOT attach the heater body sections together on the ground and attempt to hang the entire system at onetime. The weight of the individual heater body sections can cause misalignment and damage to the heater. 3. Join the body sections together and secure with tube couplings as follows: AWARNING: The following coupling tightening instructions must be followed properly to avoid future problems. a. Place the compression coupling over the end of the tube from one body section, with the tightening bolts located on the bottom and facing the installer. NOTE: There is a small hole at the centerline of the coupling that can be used to sight the end of the t...

Herunterladen

Geben Sie zwei Ziffern: