Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Napoleon Fireplaces Dateigröße: 786.97 kb Dateiname: Unterrichtssprache:

First open both side doors fully. Insert the pins on the door left side into the hinge bushings. Swing the door closed and engage the latches into the catch slots. Push the latch handles backwards to secure the closed door. It may be necessary to lift the door when securing it to ensure that it is in a horizontal position. To open the door, repeat in reverse order. CATCH SLOT DOOR LATCH HINGE PIN BUSHING FIGURES 30 LOG PLACEMENT INSTRUCTIONS PHAZERTM logs, glowing embers and charcoal embers exclusive to Napoleon Fireplaces, glow when exposed to direct flame and provide a unique and realistic glowing effect that is different in every installation. Use only certified PHAZERTM logs, glowing embers and charcoal embers available from your Napoleon / Wolf Steel Ltd. dealer. Positioning the logs improperly will cause flame impingement and carboning. Place the back log into the firebox pushing it as close to the firebox wall as possible and centered onto the log support pan. FIGURES 31 with the holes on the bottom of the log. FRONT LOG3 Set the two crossover logs into the pockets provided on both the front and rear logs., as shown. RIGHT LOG 4 Tear the glowing embers into pieces and place onto the screen beneath the front log. Care should be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the fibre hairs will glow when exposed to direct flame; however care should be taken to not block the burner ports. Blocked ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. 5 GLOWING EMBERS Randomly place the charcoal embers along the front of the support pan and some onto the screen in a realistic manner. Fine dust found in the bottom of the bag should not be used. Do not place any embers on the burner. 6 CHARCOAL EMBERS LEFT LOG Log colours may vary. During the initial use of the fireplace, the colours will become more uniform as colour pigments burn in during the heat activated curing process. W415-0153 / A / 10.29.01 REAR LOG2 SCREEN1 FRONT LOG STUDS 15 W415-0153 / A / 10.29.01 OPERATING INSTRUCTIONS The on-off switch is located on the back of the unit at the top left corner on models GDS28 and GS28. When lit for the first time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing of the logs and the "burn-in" of internal paints and lubricants used in the manufacturing process and will not occur again. Simply open a window to sufficiently ventilate the room. After extended periods of non-operation such as following a vacation or a warm weather season, the fireplace may emit a slight odour for a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to sufficiently ventilate the room. MODEL GS28 ONLY: VENTING ACTION CHECK A check for correct venting action must be made before the installed stove is left with the customer. Test in the following manner: 1. Close all doors and windows in the room / start exhaust fans in the home / turn fireplace blower off (if equipped). 2. Set controls to "high" and light the unit. 3. Wait 5 minutes. Light a match and extend it 1" into the hole located above the spill switch bracket on the adapter. 4. Venting action is satisfactory if the flame stays lit. Venting action is unsatisfactory if the flame extinguishes. 5. If venting action is unsatisfactory, turn the unit off, wait 10 minutes and try again. If the match does not stay lit, turn the unit off and check for vent blockage or restriction. If necessary, consult with a qualified inspector. Purge all gas lines with the glass door open. Assure that a continuous gas flow is at the burner before closing the door. Allow several minutes (5-15) for the flame to stabilize after ignition. MODEL GS28 ONLY: SPILL SWITCH This is a thermally activated switch, attached to the back of the chimney adapter, which senses the change in temperature and shuts down the gas valve in the event of a severe downdraft of air or a blocked or disconnected vent. It acts as a safety shutoff to prevent a build up of carbon monoxide or an explosion of unburnt gases during start up. If the flue is blocked or has no "draw", the spill switch will automatically shut off the supply of gas within about 5-10 minutes. TAMPERING WITH THE SWITCH CAN RESULT IN CARBON MONOXIDE (CO) POISONING AND POSSIBLE DEATH. OPERATION / MAINTENANCE FIGURE 32 OPERATING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE OPERATING D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the control system and any gas control which has been under water. WHAT TO DO IF YOU SMELL GAS: • Turn off all gas to the fireplace. • Open windows. • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions...

Herunterladen

Geben Sie zwei Ziffern: