Login:
Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Anleitung AEG, modell WSP 7010

Hersteller: AEG
Dateigröße: 482.51 kb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


via heating contactor£ N/PE - 50 H2 400 V i- For the Fitter 2.6 First-time Operation 2.6.1 Function Test Check the function of the fan for the storage unit by switching on the room temperature regulator. 2.6.2 Charging The units can be started without initial heating up after the function test. Charging takes place either manually with the adjuster of the mechanical charging control unit or automatically with the available Elfamatic charging control unit During initial charging, the charging in kWh must be determined and compared with the maximum permissible charging from the cold state specified in the "Technical Data". The determined charging may not exceed the maximum permissible charging from the cold state. During initial charging, a smell may be produced, the room should therefore be adequately aired / l\ (1.5 times air change, e.g. tilted windows). Initial charging in the bedroom should not take place / • \ when sleeping in it if possible. 2.7 Repair, Conversion of Unit Proceed according to these installation instructions as for the initial installation for re-installation of a unit which has been dismantled for repairs or which was in operation somewhere else, in these cases the following must be paid special attention: Parts of the thermal insulation at which there are visible signs or damage or change which could impair the safety must be replaced by new parts. The insulation must be tested and the rated consumption measured before commissioning. 2.7.1 Conversion of the Unit The instructions enclosed with the respective fitting set are applicable for conversions, additions and installations. 2.8 Transfer Explain the functions of the unit to the user. Draw his attention to the safety instructions in particular. Hand over the operating and installation instructions to the user. AEG WSP 7010 QJ 357 kg E-No. 956 042 710 F-No, 2Q200504 > 3/N/PE A&Ufo^OHz □ □qj 5,25 5,83 3QED □ roYrf 7,50 8,24 9,00 kW □ □□□□ 7 8 9 10 h -GB2J- 1/N/PE AC 230V 50Hz 1,5 kW A 26 W .5 ^>H *--- ^ ^ Made in Germany Symbols of the rating plate (Example WSP 7010) Q Total weight ) Charging Discharging -GE&- Supplementary heater A Fan 31 English For the Fitter Circuit diagram WSP 2010 - 7010 El - E6: Heating element (storage heater) □ Integr. room temperature regulator E7: Heating resistor E9: Heating resistor F1: Safety temperature limiter N6: Temperature regulator - discharging M1 - M3: Fan S2: Rocker switch - discharging N1: Temperature limiter - charging Z1: Radio interference suppressor N5: Temperature limiter - fan drawer N4: Temperature limiter - charging □ Supplementary heater XI: Mains terminal E8: Supplementary heating element X2: Terminal N2: Temperature regulator - supplementary heater N3: Temperature regulator - supplementary heater S1: Rocker switch - supplementary heater N3 ri E8 I 1 | 1 1 1 ^71_ Jr —i j 1 1 1 -qm __1 A N5 _ J Le Ilh Ilh Ile LlI X2 hr* I I k I___ — —A t ■d>/ i--< “1 N6 ttZ H t! Hi E9 !^Z1^ I I ___I___L I i 0 i ! J L. -vJ- N I N I N I I 1 L-SH I VO \iaWJ — AC-signal 230 V Charging control signal Series circuit 100 % P . „ 91.6 0/0 P Control circuit 1/N/PE - 50 Hz 230 V * when external RT is connected 83.3 °/o P 75 % P Only for WSP 2010 100 % P 3 2 1 L3 L2 L1 3 2 1 L3 L2 L1 ' N ' L31 L21 LI 1 N 1 L3 1 L21 L1 3/N/PE ~ 50 Hz 400 V 3/N/PE - 50 Hz 400 V 3 2 1 L3 L2 L1 ' N' L31 L2 L1 3/N/PE - 50 Hz 400 V 3 2 1 L3 L2 LI 1 L3 1 L2 L1 3/PE ~ 50 Hz 400 V 3 2 1 L3 L2 L1 “TH,, 1/N/PE - 50 Hz 230 V 32 For the Fitter Caution! On a 3/PE AC 50 Hz 230 V mains Rewiring of the storage heater load circuit necessary! Circuit diagram for 3/PE AC 50Hz 230 V Rewiring necessary in the storage heater! xxx pull off vi wire from E2 and plug to E6 xx pull off br wire from E6 and plug to E4 x pull off ws wire from E4 and plug to E2 E1 - E6:(storage) heater F1: protective temperature limiter N1: temperature limiter - charging N4: temperature limiter - charging X1: mains terminal 3 2 1 X1 L3 L2 L1 XI Jumpers must be wired by customer on site. 3/PE AC 50 Hz 230V Environment and recycling 3. Environment and recycling Please help us to protect the environment by disposing of the packaging in accordance with the national regulations for waste processing. Guarantee For guarantee please refer to the respective terms and conditions of supply for your country. The installation, electrical connection and first operation of this appliance should be carried out by a qualified installer. The company does not accept liability for failure of any goods supplied which are not installed in accordance with the manufacturer's instructions. 34...

Dieses Handbuch ist für folgende Modelle:
elektrische Heizungen - WSP 4010 (482.51 kb)
elektrische Heizungen - WSP 2010 (482.51 kb)
elektrische Heizungen - WSP 3010 (482.51 kb)
elektrische Heizungen - WSP 5010 (482.51 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien