Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: DeVillbiss Air Power Company Dateigröße: 1.97 mb Dateiname: Unterrichtssprache:

1. Stop engine as described in the Operation section. 2. Place the fuel valve lever in the OFF position. 3. Remove the recoil end panel as described in the Fuel Valve Bowl paragraph. 4. The fuel line can be removed from the fuel filter cover by squeezing the fuel clamp and sliding it up the fuel line. Fuel Filter Cover Fuel Clamp Cap Fuel Line 5.After removing the fuel line unscrew the cap on the fuel filter cover. NOTE: Do not loose rubber washer from fuel filter cover cap. 6. The fuel filter can now be removed to clean or replace. 7. Place new or cleaned filter into cover. 8. Press rubber washer into fuel filter cap and screw cap into fuel filter cover body. 9. Reconnect fuel line. 10. Replace and secure panel. Fuel Tank Filter Cleaning 1. Stop engine as described in the Operation section. 2. Remove gas cap and remove the fuel tank filter. 3. Clean with solvent. Wipe off excess solvent and replace fuel tank filter into tank. 4. Replace gas cap. Muffler Screen Cleaning 1. Stop engine as described in the Operation section. 2. On the exhaust end of the unit, remove the four screws securing the sides of the panel and the two fasteners with isolators securing the bottom of the panel. Carefully pull panel away from the unit noting the insulation is attached to the panel. A04669 16- ENG Screws Screws Fasteners with isolators 3. Remove the muffler screen. Muffler Screen Remove Screw and Nut Replace Spark Plug Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help your engine to start easier and run better. NOTE: Use the spark plug wrench and screwdriver supplied to remove spark plug. The spark plug is found under the top panel opposite the controls. .030" (0.76 MM) Wire Gauge Resistor NOTE: Standard spark plug: BPR4ES (NGK) Spark Plug Gap: 0.7-0.8 mm (0.028 -0.031 in) 4. Clean the muffler screen using a wire brush. 5. Replace muffler screen and secure in place. 6. Replace and secure panel. 17- ENG A04669 STORAGE If you are going to store your generator for more than 30 days, use the following information as a guide to prepare the generator for storage. Never store generator with fuel in the tank indoors or in enclosed, poorly ventilated areas, where fumes can reach an open flame, spark, or pilot light as on a furnace, water heater, clothes dryer, or other gas appliances. ENGINE PREPARATION 1. Add fuel stabilizer to fuel tank to minimize the formation of fuel gum deposits during storage. 2. Run engine at least 10 minutes after adding stabilizer to allow it to enter the fuel system. 3. Shut off engine. 4. Disconnect the spark plug wire and remove the spark plug. 5. Add one teaspoon of oil through the spark plug hole. 6. Place rag over spark plug hole and pull the recoil a few times to lubricate the combustion chamber. 7. Replace the spark plug, but do not connect the spark plug wire. NOTE: If a fuel stabilizer is not used, all gasoline must be drained from the tank and carburetor to prevent gum deposits from forming on these parts and causing possible malfunction of the engine. IMPORTANT: If gasoline is removed from the tank, oil needs to be added to prevent rust from forming in the tank: 1. Pour a cup of SAE 10W-30 oil into the gas tank. 2. With assistance from another person, shake or roll the unit so the oil covers the complete gas tank. 3. Drain off excess oil. GENERATOR • Clean the generator as outlined in the Maintenance Section on this manual. • Check that cooling air slots and openings on generator are open and unobstructed. A04669 18- ENG WATTAGE CALCULATIONS IMPORTANT Never exceed the rated capacity of your generator. Serious damage to the generator or appliance could result from an overload. 1. Starting and running wattage requirements should always be calculated when matching a generators wattage capacity to the appliance or tool. 2. There are two types of electrical appliances that can be powered by your generator: A. Items such as radios, light bulbs, television sets, and microwaves have a "resistive load". Starting wattage and running wattage are the same. B. Items such as hand tools that use an electrical motor have an "inductive load". Inductive load appliances and tools require approximately 2 to 3 times the listed wattage for starting the equipment. This initial load only lasts for a few seconds on start-up but is very important when figuring your total wattage to be used. C. Always start your largest electric motor first, and then plug in other items, one at a time. NOTE: On 120-volt loads the maximum starting wattage should NOT exceed 1250 watts. DETERMINING WATTAGE REQUIREMENTS Before operating this generator list all of the appliances and/or tools that are going to operate at the same time. (Then determine the starting wattage requirements and the running wattage requirements by following example and/or refer to household wattage calculator.) 1. First total the running wattage of all appliances and/or tools that will be operated at the same...

Herunterladen

Geben Sie zwei Ziffern: