Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
See the Wattage Calculation section in this manual to assist you in determining the appliances and tools that can be run with the wattage capacity of your generator. BEFORE START UP This generator has been shipped from the factory without oil in the crankcase. Operating the unit without oil can damage the engine. Always check engine oil level before every start. Running engine low of oil or out of oil could result in serious damage to the engine. Follow the steps listed below before starting generator: 1. Check engine oil. See the Maintenance section for correct procedure. 2. Check fuel level, fill as required. Make sure generator is turned off and has been allowed time to cool down. Use clean, fresh, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Never fill fuel tank completely. Fill tank to 1/2" below the bottom of the filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine. Never fill fuel tank indoors. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. Never run engine indoors or in enclosed, poor ventilated areas, engine exhaust contains carbon monoxide, an odorless and deadly gas. 3. Make sure generator is grounded in accordance with local requirements. 4. All electrical loads MUST be disconnected. Engine speed has been factory set to provide safe operation. Tampering with the engine speed adjustment could result in overheating of attachments and could cause a fire. Never attempt to "speed-up" the engine to obtain more performance. Both the output voltage and frequency will be thrown out of standard by this practice, endangering attachments and the user. You MUST unplug any load from the generator before starting to prevent permanent damage to any appliances. TO START THE ENGINE 1. Open the fuel shut-off valve lever. ON OFF 2. Move the choke control located to CHOKE position. NOTE: No choke is required on warm engines. Make sure choke is in the RUN position on warm engine starts. 3. Move the engine ON/OFF switch to the ON position. OFF 11- ENG A04669 4. Grasp handle on rope starter and pull slowly until resistance is felt. Let the rope rewind slowly. Pull rope with a rapid full arm stroke. Let rope rewind slowly. Repeat if necessary. 5. When engine starts, gradually move the choke to the RUN position. IMPORTANT: Allow generator to run at no load for five minutes upon each initial start-up to allow engine and generator to stabilize. STOPPING ENGINE 1. Disconnect all electrical loads. 2. Turn engine ON/OFF switch to "OFF" position. 3. Close fuel shut-off valve lever. ON OFF CONNECTING ELECTRICAL LOADS 1. Let engine run and warm up for five minutes after starting with no electrical load. IMPORTANT: If engine speed or voltage fluctuates with a load below 250 Watts, move the choke control to the half choke position. Connect loads in the following manner to prevent damage to equipment: 2. Connect inductive load equipment first; inductive loads consist of small hand tools and some small appliances. Connect the items that require the most wattage first. See Wattage Calculation Section in this manual. 3. Connect the lights next. 4. Voltage sensitive equipment should be the last equipment connected to the generator. Plug voltage sensitive appliances such as TV's, VCR's, microwaves, and cordless telephones into a UL listed voltage surge protector, then connect the UL listed voltage surge protector to the generator. Failure to connect and operate equipment in this sequence can cause damage to equipment and will void the warranty on your generator. Follow the wattage calculation table in the Wattage Calculation section of this manual. Overloading the generator will cause power fluctuations and can damage equipment and appliances. DeVilbiss Air Power Company will only be responsible for damage to customer's equipment when the generator is determined to be defective. This determination will only be made by an authorized representative of DeVilbiss Air Power Company and this decision will be final. DeVilbiss Air Power Company reserves the right to inspect the electrical connections at the customer's site of operation and test the generator for proper operation before any determination of liability is made. Failure to maintain the equipment or wiring for inspection will void any claim for damages by the customer. DeVilbiss Air Power Company will not be responsible for equipment damaged as a result of voltage surges, improper operation or improper installation of the generator. A04669 12- ENG MAINTENANCE CUSTOMER RESPONSIBILITIES TABLE MAINTENANCE TASK Before each use Every 25 Hours of Every Season Every 50 Hours of Every Season Every 100 Hours of Every Season Check oil level X See Note 2 Change oil See Note 1 Clean Air Filter Assembly X Clean Fuel Valve Bowl X Clean Fuel Filter X Clean Fuel Tank Filter X Clean Muffler Screen X Check Spark Plug X See Note 3 Prepare Unit for Storag...
Dieses Handbuch ist für folgende Modelle:Stromerzeuger - PowerBack GM1000 (1.97 mb)