Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Generac Power Systems Dateigröße: 846.53 kb Dateiname: Unterrichtssprache:

All tires must be properly inflated. Find the recommended cold tire pressures on the tire sidewall or trailer decal. Do not overinflate the tires. Tire pressures go up during driving. Checking the tire pressure when the tires are warm will give you an inaccurate pressure reading. OPERATING INSTRUCTIONS Increase the distance between your vehicle and the vehicle in front of you to twice the normal following distance when towing a trailer. Allow more following distance in adverse weather. Slow down for downgrades and shift your transmission into a lower gear. Slow down for curves, hazardous road conditions, freeway exits, and when driving in adverse weather. Heavy winds, excessive speed, load shifting or passing vehicles can cause the trailer to sway while driving. If this occurs, do not brake, speed up or turn the steering wheel. Turning the steering wheel or applying the brakes can cause the vehicle and trailer to jackknife. Let up on the gas pedal and keep the steering wheel straight. If the vehicle and/or trailer travels off the paved road, hold the steering wheel firmly and let up on the gas pedal. Do not apply the brakes. Do not turn sharply. Slow down to under 25 mph / 40 km/h. Gradually turn the steering wheel to get back on the road. Proceed with caution when entering traffic. When passing other vehicles, be sure to leave enough room for the extra length of the trailer. You will need to go much farther beyond the passed vehicle before you can return to your lane. Avoid jerky or sudden movements when turning. Part No. 97600 Genie TML-4000 and TML-4000N 20 Genie TML-4000 and TML-4000N Part No. 97600 Operator's Manual Third Edition • Second Printing Transport and Lifting Instructions Observe and Obey: Common sense and planning must be applied to control the movement of the machine when lifting it with a crane or forklift. The transport vehicle must be parked on a level surface. The transport vehicle must be secured to prevent rolling while the machine is being loaded. Be sure the vehicle capacity, loading surfaces and chains or straps are sufficient to withstand the machine weight. See the serial plate for the machine weight. Securing to Truck or Trailer for Transit Fully lower and retract the mast. See To Stow the Mast in the Operating Instructions section. Make sure the mast hold-down latch is securely locked in place. Close and secure the covers. Lower the tongue outrigger jack to support the tongue during transport. Raise and stow the outriggers. Chock the machine wheels in preparation for transport. Turn the key switch to the off position and remove the key OR lock the control panel to secure from unauthorized use. Inspect the entire machine for loose or unsecured items. Securing the Chassis Place a block on both sides of the axle behind the wheels. Place a block under the chassis at both ends of the machine. Use the two tie-down points on the machine for anchoring down to the transport surface. Use chains or straps of ample load capacity. Use a minimum of 2 chains to secure the chassis. Adjust the rigging to prevent damage to the chains. Third Edition • Second Printing Operator's Manual Part No. 97600 Genie TML-4000 and TML-4000N 21 Observe and Obey: Only qualified riggers should rig and lift the machine. Be sure the crane capacity, loading surfaces and straps or lines are sufficient to withstand the machine weight. See the serial plate for the machine weight. TRANSPORT AND LIFTING INSTRUCTIONS Lifting the Machine With a Crane Fully lower and retract the mast. See To Stow the Mast in the Operating Instructions section. Make sure the mast hold-down latch is securely locked in place. Close and secure the covers. Inspect the entire machine for loose or unsecured items. Use the lifting eye mounted on the mast to lift the machine. Operator's Manual Third Edition • Second Printing Decals Decal Inspection Use the pictures on the next page to verify that all decals are legible and in place. Below is a numerical list with quantities and descriptions. Part No. Description Quantity 28159 Label - Diesel 1 28161 Warning - Crushing Hazard 6 28164 Notice - Hazardous Materials 2 28171 Label - No Smoking 1 31072 Manual Storage Container 1 52475 Label - Transport Tie-down 2 62707 Warning - Tow Speed 1 65408 Notice - Operating Instructions 1 65409 Notice - Mast Rotation Instructions 1 65411 Warning - General Safety 1 65412 Warning - Transport Instructions 1 65414 Danger - Electrocution Hazard 2 65421 Warning - Electrocution, Generator 2 65423 Notice - Deutz Engine Specs 1 72008 Caution - Turn Off Lights 1 72009 Cosmetic - Genie TML-4000 2 72010 Cosmetic - Genie TML-4000N 2 Part No. Description Quantity 72870 Caution - Component Contact 2 72871 Label - Power Outlet, 120V 1 72874 Label - Locked, Unlocked 1 72889 Warning - Transport Hazard 1 72890 Notice - Mast Retraction 1 72891 Label - Blue Arrow 2 82219 Label - Power Outlets Under Cover 1 82222 Caution - Light Storage, Standard Models 1 82223 Label - Light Storage, S...

Herunterladen

Geben Sie zwei Ziffern: