Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
• 3 Dry/ChargeDryCharge100 min 0 to 60 min It is possible to change to the “Clean/Dry/ Charge” course even after the “Dry/Charge” course has started. • CourseTime required (guide) 1 ChargeCharge0 to 60 min 2 Clean/Dry/ ChargeCleanDryCharge10 min 50 min (80 min*) 0 to 60 min It is not possible to change the course after the “Clean/Dry/Charge” course has started. • 3 Dry/ChargeDryCharge100 min 0 to 60 min It is possible to change to the “Clean/Dry/ Charge” course even after the “Dry/Charge” course has started. • * When the ambient temperature of the self.cleaning recharger is low (approx. 15 °C (59 °F) or lower), the time it takes to dry the shaver increases. • The Clean or Dry function may stop under extreme low temperatures (approx. 0 °C (3 °F) or lower). In such a case, the CLEAN and DRY lamps will blink when the “Clean/Dry/Charge” course is selected, or the DRY lamp will blink when the “Dry/ Charge” course is selected. .Follow the steps outlined below if the status lamp blinks or glows Blinks Correctly set the detergent cartridge and then restart a course. If the status lamp goes outContinue a course. When an abnormality has been corrected Remove the AC adaptor from a household outlet. When the status lamp goes out Glows Remove the shaver from the self.cleaning recharger and then check that the [CLEAN] lamp has gone out. (Be careful as the blade may be hot or wet.) Check that the water tank is correctly attached, the water tank cap is securely closed and the self.cleaning recharger is placed horizontally. When no abnormality was found It is time to replace the detergent cartridge and cleaning liquid inside the water tank. Wash away the old cleaning liquid and then rinse the water tank and then refill it with water. Replace the old detergent cartridge and then restart the course. When the status lamp glows again Contact an authorized service center. Continue a course. 11 English Cleaning the shaver without the self-cleaning recharger 1. Disconnect the power cord from the shaver. 2. Apply some hand soap and some water to the outer foil. 3. Rotate the lock ring to unlock the power switch. 4. Press the power switch for more than 2 seconds to activate the sonic vibration cleaning mode. The battery capacity lamps blink in order. After about 20 seconds, it will be automatically turned off, or you can turn it off by pressing the power switch. 5. Remove the outer foil section and press the power switch for more than 2 seconds to activate the sonic vibration cleaning mode and clean it with running water. 6. Wipe off any drops of water with a dry cloth. 7. Dry the outer foil section and the shaver completely. 8. Attach the outer foil section to the shaver. • • 4 5 7 Drying the shaver with the self-cleaning recharger 1. Attach the outer foil section to the shaver. 2. Dry the shaver with self-cleaning recharger using “Dry/ Charge” course. Replacing the system outer foil and the inner blades system outer foil once every year inner blades once every two years Replacing the system outer foil 1. Press the foil frame release buttons and lift the outer foil section upwards. 2. Press the system outer foil release buttons and pull down the system outer foil. 3. Align the foil frame mark ( ) and the system outer foil mark ( ) and securely attach together. The system outer foil cannot be reversely attached. Always insert the system outer foil to the foil frame when attaching to the shaver. 4. After turning the foil frame mark ( ) to the front, securely attach the outer foil section to the shaver until it clicks. • • 1 2 3 Replacing the inner blades 1. Press the foil frame release buttons and lift the outer foil section upwards. 2. Remove the inner blades one at a time. Do not touch the edges (metal parts) of the inner blades to prevent injury to your hand. 3. Insert the inner blades one at a time until they click. • 1 2 3 . . Englis h .Replacement parts Replacement parts are available at your dealer or Service Center. System outer foil and inner WES9013 blades Replacement parts for ES.LT71 System outer foil WES9087 Inner blades WES9068 Detergent cartridge WES035 Cleaning the self.cleaning recharger Beard trimmings may become attached to the cleaning tray of the self.cleaning recharger. Follow the steps below to remove them. We recommend doing this each time you change the detergent cartridge. 1. Be sure to remove the water tank and the appliance plug from the self.cleaning recharger. • Be careful not to spill the cleaning liquid. . Gently wipe off any beard trimmings attached to the inside of the cleaning tray with a cloth or tissue paper dampened with water. • Clean the corners and uneven parts of the cleaning tray with a cotton swab dampened with water. 12 . 1 Do not pull hard on the rubber blade protector (a) at the bottom of the cleaning tray. The rubber may come off if you pull hard on it. It is only necessary to pull it up slightly. Warning Do not wash or apply water to the AC adaptor or selfcleaning recharger. Failure to...