Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
To accomplish this, complete the following steps: Check Water's Chemical Analysis: Sears sells a complete line of water treating equipment to correct various water problems. To be sure you have the proper type and size equipment, You must have your water tested. Your Sears store can give you a water test results for hardness, iron and acidity, and tell you what equipment you need. Simply take at least a 4 oz. sample of your water to Sears, and they will test it while you wait. If you need help to get your water tested, or if you have other questions about your water, ask at your Sears store. NOTE: Add these readings to the Facts and Figure table on page 3. Check Your Water Pressure: For your softener to work right, a water pressure of no lower than 20 pounds per square inch (psi) is needed in the house water pipes. The highest pressure allowed in the water pipes is 125 psi. If pressure is over 125 psi, buy and install a pressure reducing valve in the water inlet pipe to the soften er. NOTE: If water pressure during the day is 100 psi or more, pressure during the night may go over 125 psL Adding a pressure reducing valve may reduce the flow. NOTE: Add these readings to the Facts and Figure table on page 3. If you have a well water system, look at the pressure gauge to find the water pressure. Call your local water department if you have city water. They will tell you what the water pressure is where you live. NOTE: Add these readings to the Facts and Figure table on page 3. Check your water flow rate: A water flow of at least 3 gallons per minute is needed. A lower flow will keep your softener from working as well as it should. Complete the following steps to make an easy check of your flow rate. 1. Fully open two cold water faucets close to the point water enters the house. 2. With both faucets open, fill a gallon container at one faucet while looking at a watch or clock to see how many seconds it takes. 3. Empty the container and go to the second faucet (be sure BOTH faucets are still on). Fill the gallon container at the second faucet and see how many seconds it takes. 4. Turn off both faucets. Now add the number of seconds it took to fill the container at both faucets. 5. A total of 90 seconds, or less, means the system flow rate is good. NOTE: Add these readings to the Facts and Figure table on page 3. NOTE: Codes in the state of Massachusetts require installation by a licensed plumber. For installation, use plumbing code 248CMR of the Commonwealth of Massachusetts. Questions? Call The Kenmore Water Line 1-800-426-9345 ASSEMBLE INLET OUTLET ADAPTORS, OR SINGLE BYPASS VALVE Complete the following steps to assemble the adaptors or bypass valve. 1. Close the shutoff valve on the house main water pipe, near the water meter or pressure tank, to turn off the water. See Fig. 7. 2. Shut off the gas or electric supply to the water heater. See Fig. 7. 3. Open the highest and lowest water faucets in your house. This will let water drain from the pipes. Close faucets after water has drained. 4. Remove the main cover. See Fig. 8. Pull outward on two (2) tabs to release. The salt hole cover remains attached to the main cover when removed. Set both covers aside so they will not get scratched or broken. INSTALL SEARS BYPASS VALVE AND / OR THE INLET OUTLET THREADED ADAPTORS NOTE: If you will not install the bypass valve because you will have a three (3) valve bypass, skip steps 6 & 7, but do steps 5 and 8. 5. Visually check and remove any foreign materials from the valve inlet and outlet ports. See Fig. 9. Carefully remove the two large plastic clips (you will use them). Check to be sure the turbine and turbine support are firmly in place. See Fig. 10. BYPASS VALVE: 6. Put a light coating of silicone grease on the o-ring seals and slide onto the bypass valve. 7. Push the bypass valve into the softener valve as far as it will go. Snap the two large holding clips into place, from the top down as shown. See Fig. 11. CAUTION: Be sure the clips snap firmly into place so the bypass valve will not pull out. See Fig. 11. INLET AND OUTLET THREADED ADAPTORS: 8. Put a light coating of silicone grease on the o-ring seals and slide into the threaded adaptors. Push the adaptors into the valve inlet and outlet ports, or bypass valve ports, as far as they will go. Both adaptors are the same and fit either port. Snap the two large holding clips into place, as shown. See Fig. 11. CAUTION: Be sure the clips snap firmly into place so the tubes will not pull out. See Fig. 11. Shutoff Shutoff . Pressure Valve Valve L/Tank Pump Electrical Panel FIG. 7 Salt Hole Cover Cover (Main) FIG. 8 INSTALLING BYPASS VALVE, AND/OR INLET AND OUTLET THREADED ADAPTORS Valve Outlet Included with Softener Valve Inlet Included with Softener FIG. 9 Questions? Call The Kenmore Water Line 1-800-426-9345 INSTALLING HOLDING CLIPS Before installing the bypass valve, or copper tube, be sure the turbine and support are firmly in place in the valve outlet port. Bypass V...
Dieses Handbuch ist für folgende Modelle:Rasierer - 625.39356 (2.96 mb)