Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Hersteller: Bosch Dateigröße: 597.93 kb Dateiname: 926246en.pdf Unterrichtssprache:

• With metal fronts use the cleaners that are commercially available. Oven interior Clean the appliance after each use. In this way, residues are easier to clean off and are not allowed to burn on. 1.To clean the oven, switch the oven light on. 2.After every use, wipe the oven with a solution of washing-up liquid and allow to dry. 3 Remove stubborn residues with a special oven cleaner. 1 Warning: If using an oven spray, please follow the manufacturer's instructions exactly. Accessories Wash all slide-in units (shelf unit, baking tray, shelf support rails etc.) after each use and dry well. Soak briefly to make them easier to clean. Shelf Support Rails The shelf support rails on the left and right hand sides of the oven can be removed for cleaning the side walls. Removing the shelf support rails First pull the front of the rail away from the oven wall (1) and then unhook at the back (2). Fitting the shelf support rails 3 Important! The rounded ends of the guide rails must be pointing forwards! To re-insert, first hook the rail into place at the back (1) and then insert the front and press into place (2). Oven Lighting 1 Warning: Risk of electric shock! Prior to changing the oven light bulb: – Switch off the oven! – Disconnect from the electricity supply. 3 Place a cloth on the oven floor to protect the oven light and glass cover. Changing the oven light bulb/ cleaning the glass cover 1.Remove the glass cover by turning it anti-clockwise and then clean it. 2.If necessary: replace with 25 watt, 230 V, 300 °C heat-resistant oven lighting. 3.Refit the glass cover. Oven Roof The upper heating element can be folded down to make it easier to clean the oven roof. Folding down the heating ele ment 1 Warning: Only fold down the heating element when the oven is switched off and there is no risk of being burnt! 1.Remove the side shelf support rails. 2.Grip the heating element at the front and pull it forwards and out over the support lug on the inner wall of the oven. 3.The heating element will now fold down. 1 Caution: Do not use force to press the heating element down! The heating element might break. Clean the oven roof Repositioning the heating element 1.Move the heating element back up towards the oven roof. 2.Pull the heating element forwards against the spring pressure and guide it over the oven support lug. 3.Settle it onto the support. 4.Insert shelf support rail. 1 Important: The heating element must be positioned correctly and securely on both sides above the support lug on the inner wall of the oven. Oven Door The door of your appliance may be removed for cleaning. Removing the oven door 1.Open the oven door completely. 2.Completely fold back the clamp ing levers on both door hinges. 3.Grip the oven door with both hands and close it about 3/4 going past the point of resistance. 4.Pull the door away from the oven (Caution: the door is heavy!) 5.Place the door, with the outer surface downwards, on a soft, flat surface, (for example on a blanket) to avoid scratches. Hanging the oven door 1.From the side of the door on which the handle is positioned, take hold of the sides of the door with both hands. 2.Hold the door at an angle of approx. 60°. 3.Insert the door hinges as far as possible into the two slots on the right and left at the bottom of the oven at the same time. 4.Lift the door up until resistance is met and then open it fully. 5.Fold the clamping levers on both door hinges back into their original position. 6.Close the oven door Oven Door Glass The oven door is fitted with two glass panels mounted one behind the other. The inner panel can be removed for cleaning. 1 Caution: the following steps must be performed only with the oven door removed! If the glass is removed while the door is attached, the lighter weight may cause it to spring up and cause injury. 1 Important! Rough handling of the glass, especially at the edges of the front panel, may cause it to break. Removing the glass from the door 1.Detach the door and, with the handle downwards, place it on a soft, even surface. 2.Grasp the top glass panel underneath, and push it towards the door handle against the pressure spring, until it comes free (a). 3.Hold the panel gently underneath, and slide it out (a). Clean the glass panel Inserting the glass to the door 1.Insert the panel at an angle from above into the section of the door in which the handle is located (a). 2.Lower the panel. Place the glass against the pressure spring at the handle end, and in front of the retaining frame at the bottom of the door, then push it into the frame (a). The glass panel must be firmly attached! Re-hang the door to the oven. What to do if … Problem Possible cause Remedy The oven does not heat up The oven is not switched Switch the oven on on The clock is not set Set the current time on the clock The necessary settings have Check the settings not been carried out A fuse in the house’s wiring Check fuses system (in the fuse box) If the fuses trip several has tripped...

Herunterladen

Geben Sie zwei Ziffern: