Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Korg Dateigröße: 7.58 mb Dateiname: Unterrichtssprache:

4. The step keys will light to indicate the trigger locations of the pattern for that part. Press the step key for the step whose pitch you wish to edit (the key will blink). By pressing a step key where a trigger exists, you can audition its pitch. 5. Rotate the dial to modify the pitch of that step. When the display is showing the Pitch, pressing a step key will not switch its trigger on/off. Changing the pitch of a step whose trigger is off will have no effect. If you turn that trigger on, the specified pitch will be used. If you wish to transpose the pitch for one part of the entire pattern, refer to p.30 "Changing the pitch data of a part (Pitch Shift)." 2 4 3 5 The pitch will be shown in the display as follows. Display for D Display for A .1 3 Display for B4 Changing the gate time GATE TIME 0.25...64.0 1. Turn off the Keyboard function key (the key will go dark). 2. Use the cursor keys to make the parameter select LEDs indicate GATE TIME. 3. Use the PART SELECT key to select the part that you wish to edit. 4. The step keys will light to indicate the trigger locations of the pattern for that part. Press the step key for the step whose gate time you wish to edit (the key will blink). By pressing a step key where a trigger exists, you can audition its pitch. 5. Rotate the dial to modify the gate time of that step. The value shown in the display is the gate time length in units of a step. For example if the gate time is set to 1.0, the gate time will be exactly as long as one step. If the gate time length extends into the timing of the next note, the filter EG of the next note will not be retriggered. When the display is showing the Gate Time, pressing a step key will not switch its trigger on/off. Changing the gate time of a step whose trigger is off will have no effect. If you turn that trigger on, the specified gate time will be used. 2 4 3 5 a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a4.Pattern mode 4.Pattern mode 29 Convenient functions for editing patterns If you wish to save the pattern you edit using these functions, you must perform the Write operation before selecting a different pattern or turning off the power. Erasing phrase pattern data from a part To erase the phrase pattern data for the selected part, you can use one of the following two methods in addition to turning each of the sixteen step keys off. Erasing data during playback or recording (ERASE) 1. Press the PART SELECT key to select the part from which you wish to erase data. 2. During playback or recording, hold down the SHIFT key and press the Rec key. As long as you continue holding these keys, trigger data will be automatically be erased from the selected part. Performing this operation will not affect the pitch and gate time data. 2 2 1 Erasing all data from a part (CLEAR PART) This operation erases all phrase pattern and motion sequence data at once. 1. If the pattern is playing, press the Stop/Cancel key to stop playback. 2. Press the PART SELECT key to select the part whose data you wish to erase. 3. Hold down the SHIFT key and press step key 12 (CLEAR PART). (Key 12 will blink.) 4. Once again press step key 12 to clear the data. To cancel without clearing the data, press the Stop/Cancel key. When you perform this operation, the pitch of all steps will be set to "C4," and the gate time to "1.00." 3 3,4 2 Motion sequence Playing a motion sequence A motion sequence can be played back in one of the following two ways, and you can select the playback method independently for each part. SMOOTH: Knob values will be connected smoothly, and the sound will change smoothly. TRIG HOLD (trigger hold): The value of the motion sequence knob will be held at the note timing of that part. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 On On On On On On On On 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 On On On On On On On On 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 On On On On On On On On Playback the motion sequence with Trig Hold setting Knob movements when the motion sequence was recorded Playback the motion sequence with Smooth setting There will be no effect when the Motion Sequence LED is dark (off). Recording a motion sequence You can record knob movements (motion sequence) for each part. When recording a motion sequence, only one knob is valid for each part. If you record a motion sequence on the same part using a different knob, the effect of the previously recorded knob will disappear. For the recording procedure, refer to p.18 "Using a motion sequence" in section 3. Basic operation (Quick Start). Motion sequences are recorded in realtime while you listen to the playback. It is not possible to partially modify a motion sequence after it has been recorded. You will need to keep trying until you record a motion sequence to your liking. (Refer to p.31 "Erasing motion sequence data from a part.") Checking motion sequence data Hold down the SHIFT key and press the MOTION SEQ key. If motion sequence data has been ...

Herunterladen

Geben Sie zwei Ziffern: