Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: GE Dateigröße: 826.82 kb Dateiname: SCR_OM_FINAL.pdf Unterrichtssprache:

The part numbers of the stacking kits are 02664, for use on the SCR-6 and SCD-6, and 02665 is used on the SCR-8 and SCD-8. See page 2-4 for single power cord installations. 1. Lay unit on its side and bolt locking casters or legs, to the control side of unit. 2. Using the bolts provided for the non-locking casters, or legs, bolt both the stacking spacer (provided in the kit) and the non-locking caster, or legs, to the front side of the unit. The stacking spacer should extend out the front of the unit about three inches. 3. Carefully lift the rotisserie and place it on top of the display, or bottom rotisserie, with the controls on the same side. 2-2 303 SCR-6/8 2-4. STACKING INSTRUCTIONS (Continued) Take care when moving the unit to prevent personal injury. The SCR-8 weighs approximately 500 lbs. (230 kg) and the SCR-6 weighs 380 lbs. (172 kg). 4. Remove the three side panel screws from the top unit and remove the three top side panel side screws from the bottom unit. 5. Mount the stacking brackets to each side of the units, as shown in Figure 1, using the screws removed in step 4. 6. Unit is now ready for use. Figure 1 For units being installed in Canada, for Price Costco, proceed with the following steps: 7. Remove the black plug button from the top of the upper unit. Figure 2 8. Remove the screws from the channel assembly and take the top two parts apart. 9. Remove the screws along the corners of both top and bottom units. 10. Mount one side of the channel to the units, using the screws previously removed in step 9. See Figure 2. 11. Route the power cord up through the mounted channel and attach the cover to the channel, using the screws previously removed in step 8. See Figure 2. 12. Unit is now ready for use. 203 2-3 SCR-6/8 Figure 1 2-5. STACKING INSTRUCTIONS 1. Lay unit on its side and bolt locking casters or legs, to FOR SINGLE POWER CORD the control side of unit. UNITS 2. Using the bolts provided for the non-locking casters, or legs, bolt both the stacking spacer (provided in the kit) and the non-locking caster, or legs, to the front side of the unit. The stacking spacer should extend out the front of the unit about three inches. 3. Carefully lift the rotisserie and place it on top of the display, or bottom rotisserie, with the controls on the same side. Take care when moving the unit to prevent personal injury. The SCR-8 weighs approximately 500 lbs. (230 kg) and the SCR-6 weighs 380 lbs. (172 kg). Figure 2 4. Remove the control side, side panels from both units. 5. Route the power cord inside of the SCD as shown in Figure 1. 6. Thread the SCD power cord up through both units, using the hole in the center, top of the SCD. See figure 2. Figure 3 7. Using a flat-head screwdriver, mount the power cord wires to the contactor terminals shown in figure 3. 8. Replace side panels, mounting the stacking brackets to each side of the units, as shown in Figure 1 (page 2-3), using the screws removed in step 4. 9. Unit is now ready for use. SCR-6/8 2-6. STACKINGAND OUTBOARD CASTER INSTALLATION INSTRUCTIONS 1. Using a Phillip’s head screwdriver, remove the 8, 1/4-20 x 1 in. screws in the corners of the unit. Figure 1. 2. Remove all contents from inside of unit. Carefully lay the unit over onto the customer side of the unit. Be sure to protect the glass door from damage, such as placing packing materialbetween unit and a wood pallet. (If the door on the customer side has a handle on it, allow the door handle to hang over the edge to the wood pallet.) 3. Using a 7/16 in. wrench or socket, remove the bolts, washers and lockwashers from the bottom of the unit. 4. Using the hardware removed in step 3, and the caster mounting holes in the bottom of the unit, fasten the outboard caster brackets to the bottom of the unit, along with the stacking spacer, if present. (The stacking spacer should be on the customer side of the unit.) Then, using 8, 1/4-20 x 1 in. screws (from step 1) fasten the caster brackets to both sides of the unit. Figures 2 & 3. Figure 1 Figure 2 Figure 3 The brackets can be used on either side, thus the 16 mounting holes in the bracket, shown in Figure 2. 105 2-5 SCR-6/8 Figure 4 2-6. STACKINGAND OUTBOARD CASTER INSTALLATION INSTRUCTIONS (Continued) 5. Attach casters to the caster bracket (Figure 4), mounting the two locking swivel casters to the control side of the unit and the non-locking casters to the customer side. Use the 5/16 inch hex head bolts, 5/16 inch locking washers, 5/16 inch nuts and 5/16 inch flat washers (use 2 flat washers per bolt; one on the bottom side of caster bracket and one on the top-side) which are provided. Completed installation shown in Figure 5. 6. Set the unit onto its casters and carefully lift the rotisserie and place it on top of the display, or bottom rotisserie, with Figure 5 the controls on the same side. Figure 6 Take care when moving the unit to prevent personal injury. The SCR-8 weighs approximately 500 lbs. (230 kg) and the SCR-6 weighs 380 lbs. (172 kg). 7. R...

Herunterladen

Geben Sie zwei Ziffern: