Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: AEG Dateigröße: 900.05 kb Dateiname: 944925EN.pdf Unterrichtssprache:

• Clean all accessories (with a soft cloth with warm water and cleaning agent) after each use and let them dry. • If you have nonstick accessories, do not clean them using an aggressive agents, sharp edged objects or dishwasher. It can cause a damage to the nonstick coating. Pyrolytic cleaning Remove all parts from the oven. Do not start the pyrolytic cleaning if: • If you do not remove the shelf support or telescopic shelf runners (if supplied) - the display shows 'C1' on some models. • if you do not close the oven door correctly- the display shows 'C3' on some models. 1. Remove the worst of the residual dirt manually. 2. Set the Pyrolytic cleaning function (refer to section "Oven functions"). 3. When flashes, press or to set the necessary procedure: – P1 1:30 for a low degree of dirt, – P2 2:30 for a usual degree of dirt, After 2 seconds procedure starts. To change length of selected procedure (P1 or P2), press to set , then press or to set length for the pyrolytic procedure. You can use the End function to delay start of the cleaning process. When the oven reaches pre-set temperature, the door locks. The symbol and the bars of the heat indicator come up, until the door unlocks again. During pyrolytic cleaning the lamp is off. Cleaning reminder To remind you that the pyrolytic cleaning is necessary the cleaning reminder symbol flashes in the display PYR after every activating and deactivating the appliance for the next 10 seconds. The cleaning reminder goes off the display: • after end of the pyrolytic cleaning function; • if you use or , when is flashing; Shelf support You can remove the shelf support to clean the side walls. Care and cleaning 27 Removing the shelf support 1. Pull the front of the shelf support away from the side wall. 2. Pull the shelf support from the back of the side wall to remove it. To install the shelf support follow the procedure in reverse. Valid with telescopic runners: The retaining pins on the telescopic shelf runners must point to the front! 12 Oven lamp WARNING! There is a risk of electrical shock. The oven lamp and the lamp glass cover can be hot. Before you change the oven lamp: • Deactivate the appliance. • Remove the fuses from the fuse box or deactivate the circuit breaker. CAUTION! Put a cloth on the bottom of the interior of the appliance. It prevents damage to the lamp glass cover and the cavity. Replacing the oven lamp: 1. You can find the lamp glass cover at the cavity ceiling. Turn the lamp glass cover counterclockwise to remove it. 2. Clean the glass cover. 3. If necessary, replace the oven lamp with applicable 300°C heat-resistant oven lamp. Use the same oven lamp type. 4. Install the glass cover. 28 28 Care and cleaning Door and glass panels To clean the door, remove it. CAUTION! Be careful when you remove the door from the appliance. The door is heavy! Removing the door 1. Open the door as far as it goes. 2. Fully press clamping levers (A) on the two door hinges. 3. Close the door until the first position (angle approximately 70°). 4. Hold of the door with one hand on each side and pull it away from the at an up angle. AA To install the door follow the procedure in reverse. The number of glass panels if different for the different models. CAUTION! Put the door with the outer side down on a soft and level surface to prevent scratches. Removing and cleaning the door glass panels 1. Remove the door. 2. Hold the door trim (B) on the top edge of the door at the two sides and push inwards to release the clip seal. 3. Pull the door trim to the front to remove it. B 4. Hold the door glass panels on their top edge one by one and pull them up out of the guide 5. Clean the door glass panels. To install panels follow the procedure in reverse. Install the smaller panel first, then the larger. What to do if… 29 WHAT TO DO IF… WARNING! Refer to "Safety information" chapter. Problem Possible cause Solution The oven does not heat up The appliance is switched off Switch on the appliance The oven does not heat up The clock is not set Set the clock. Refer to "Setting the clock" The oven does not heat up The necessary settings are not set Make sure, the settings are correct The oven does not heat up The automatic cut-out is switched on Refer to „Automatic cut-out“ The oven does not heat up The fuse is released Make sure, if the fuse is the cause for the malfunction. If the fuse releases again and again, refer to an authorized electrician The oven lamp does not operate The oven lamp is defective Replace the oven lamp. The pyrolytic cleaning does not operate (the clock display shows „C1“) The shelf support/telescopic runners are not removed Remove support/telescopic runners The pyrolytic cleaning does not operate (the time display shows „C3“) The display shows F102 The door is not correctly closed or door lock is defective • The door is not closed correctly • The door lock is defect Close the door correctly • Close the door correctly • Switch off the appliance with the house fuse o...

Herunterladen

Geben Sie zwei Ziffern: