|
Anleitung Zusammenfassung
.531" I.D. x 937 4 711-0579 Flail Spacer 7/32" Lg. O.D. x .09 5 11455 Cutting Finger 33 11459 Flail 6 736-0921 L.-Wash. 1/2" Scr.* 34 711-0564 Flail Spacer 23/32" Lq. 7 726-0111 Palnut 3/16" Dia. 35 711-0578 Clevis Pin .50" Dia. x 3.0" Lq. 8 712-0922 Hex Jam Nut 1/2-20 Thd.* 36 736-0247 FI.-Wash. .406" I.D. x 1.25" 9 714-0507 Cotter Pin 3/32" Dia. x 3/4" O.D. Hdn. Lg.* 37 736-0217 L.-Wash. 3/8" Scr. H.D. 10 11465-488 Chute Deflector 38 710-0151 Hex Bolt 3/8-24 x 2.00" Lg. 11 712-0107 L.-Nut 1/4-20 Thd. H.T. 12 710-0289 Hex Bolt 1/4-20 x.50" Lg.* 39 14575-488 Flail Housing Ass'y. -Comp. 13 714-0114 Sq. Key 1/4" x 2.00" Lg.* 40 712-0107 Hex Cent. L-Nut 1/4-20 Thd. 14 13430 Impeller Assembly 41 11477 Upper Guide Extension 15 710-0157 Hex Bolt 5/16-24x3/4" Lg.* Ass'y. 16 736-0119 L-Wash. 5/16" Scr.* 42 11478 Hinge Pin 17 14573 Hopper to Engine Mtg. Plate 43 726-0111 Palnut 3/16" Dia. 18 Engine 44 712-0109 Wing Nut Elastic 1/4-20 Thd. 19 11464 Engine Mounting Plate 45 13431 Blade 20 712-0123 Hex Nut 5/16-24 Thd.* 46 11460-488 Guide Extension Assembly 21 736-0119 L.-Wash. 5/16" Scr.* 47 11472-488 Guide Extension 22 738-0521 Shaft 48 736-0264 FI.-Wash. 5/16" Scr.* V 49 11481-488 Hopper Assembly ¿3 736-0170 Special L.-Wash. 5/16" I.D. 50 710-0601 Hex Wash. Hd. Self-Tap Scr. 24 726-0221 Push Cap 5/16-18 x .50" Lg. 25 711-0494 Spacer 51 11479 Clamp Rod Assembly 26 734-1056 Wheel Ass'y. -Comp. 52 11454 Back-Up Plate 27 736-0100 FI.-Wash. .50" I.D.* 53 11467 Inlet Guide Assembly 28 710-0624 Hex Bolt 5/16-24 x 1.50" 54 09966 Knob Ass'y. Lg.* 55 11480 Stop Washer 29 712-0429 Elastic Stopnut 5/16-18 Thd. 56 710-0542 Hex Bolt 5/16-18 x 8.38" Lg. 30 710-0237 Hex Bolt 5/16-24 x .62" Lg.* 57 15798 Deflector Side Plate 764-0+26" Bag (Not Shown) PIMA (615 - Red) (488- Mack Truck Yellow) *por faster service obtain standard nuts, bolts and washers When ordering parts, if color or finish is important use the ap- locally. If these items cannot be obtained locally, order by propriate color code shown above (e.g. Mack Truck Yellow part number and size as shown on parts list. Finish—11907 (488).) The engine is not under warranty by the shredder manufacturer. If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the “Yellow Pages" of your telephone book under “Engines—Gasoline.” Find It Fast In The Yellow Pages This instruction manual covers various models and all specifications shown do not necessarily apply to your model. Specifications subject to change without notice or obligation. 11 I TROUBLE SHOOTING CHART PROBLEM CAUSE REMEDY 1. Material not Shredding. Blade and/or Flails not Sharp. Sharpen or Reverse Blade and Flails. 2. Excessive Vibration A. Bent Cran cshaft. B. Out of Balance Conditon in Plate Asi embly. A. Replace Crankshaft (should be done by an Authorized Service Dealer). B. Replace Impeller Assembly. 3. Engine Boqs Down or Stalls. A. No Gas in Fuel Tank. B. Feeding Material into the Machine too Quickly. A. Fill Tank if Empty. B. Do Not Force Material through Openings, Gradually Feed Material into Openings. 4. Engine Fails to Start. A. Check Fuel Tank for Gas. B. Spark Pluc Lead Wire Disconnected. C. Faulty Spc rk Plug. A. Fill Tank if Empty. B. Connect Lead Wire. C. Spark Should Jump Gap Between Control Electrode and Side Electrode. If Spark does not jump. Replace the Spark Plug. 5. Hard Starting or Loss of Power. A. Spark Pluc Wire Loose. B. Dirty Air Cleaner. A. Connect and Tighten Spark Plug Wire. B. Clean Air Cleaner as Described in Engine Manual. 6. Engine Overheats. A. Carburetoi Not Adjusted Properly B. Air Flow Restricted. C. Engine Oil Level Low. A. Adjust Carburetor. See Engine Manual. B. Remove Blower Housing and Clean as Described in the Engine Manual C. Fill Crankcase with the Proper Oil. NOTE: For repairs beyond the minor adjustments listed above, please contact your local service dealer. MTD PRODUCTS INC ...................... YaRD-MaN COMPANY P.O. BOX 3690C • CLEVELAND OHIO 44136...
Dieses Handbuch ist für folgende Modelle:Häcksler - 245-650-000 (1.26 mb)