Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Keep proper balance and footing at all times. 10. The engine governor settings on your machine must not be altered, changed, or tampered with. The governor controls the maximum safe operating speeds and protects the engine and all moving parts from damage caused by overspeed. 11. Do not transport machine while engine is running. MAINTENANCE AND STORAGE 1. When this equipment is stopped for servicing, inspection, storage or to change an accessory, make sure the spark plug wire is disconnected from the spark plug. The machine should be allowed to cool down before making such inspection, adjustments, service, etc. Maintain your machine with care and keep it clean for the best and continued safe operation. 2. When not in use, your machine should be stored out of the reach of children. Keep where gasoline fumes will not reach an open flame or spark. For long periods of storage, the gasoline should be drained and disposed in a safe manner. Always allow the machine to cool before storing in any enclosure. 3 NOTE The right and left side of your shredder is determined from operator's position. SHREDDER FIGURE 1 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY 1. (1) 7/16" Open End or Box Wrench 2. (1) 1/2" Open End or Box Wrench 3. (1) Adjustable Wrench 1. Remove the shredder, hardware pack and all parts and literature from the carton before discarding carton. eSSsls JsîSi3* —t = u M y B m c B CHI Œ31 rrn n era r €)\ it) FIGURE 2 CONTENTS OF HARDWARE PACK A (3) Hex washer head self-tapping screws B (8) Hex screws 1/4-20 x 1/2" long C (8) Hex center lock nuts 1/4-20 thread 4 2. Insert the deflector side plates inside the chute deflector, one on each side. Place the chute and deflector side plates in position on the left hand side of shredder. 3. Secure with four hex screws (B) and hex center lock nuts (C). Heads of screws are assembled from the inside. Nuts go on the outside. Start all four screws and nuts, then tighten with an adjsutable wrench and 7/16" wrench. See figure 3. FIGURE 3 V Place the hopper on the shredder. Start all three self-tapping screws (A) by hand, then tighten with a 1/2" wrench. See figure 4. FIGURE 4 5. Loosen the hand knob on the right hand side of the shredder. See figure 5. 6. Place upper guide extension in place on guide extension. Secure with four hex screws (B) and hex center lock nuts (C). A 7/16" wrench and adjustable wrench are required. See figure 5. FIGURE 5 5 I OPERATION BEFORE STARTING ENGINE 1. Fill fuel tank with fresh regular gasoline. Dd Not mix oil with gasoline. 2. Fill crankcase with oil. Refer to separate e îgine manual packed with your shredder. TO START ENGINE Tecumseh Engine 1. Place control lever (on engine) in "RUN" position. See figure 7. 2. For cold engine start, move carburetor ccntrol to "CHOKE" position. See figure 7. NOTE A warm engine may not require choking. CONTROL LEVER N START POSITION CARBURHTOR CONTROL (CHOKE) 3. Pull rewind starter using a quick, full arm stroke. Keep a firm grip on the handle. Return rope slowly. 4. After engine starts, move choke lever on carburetor gradually to "OFF" position. Briggs and Stratton Engine 1. Place control lever (on engine) in "CHOKE" position. See figure 7A. NOTE A warm engine may not require choking. Simply place control lever in "RUN" Position. FIGURE 7 - TECUMSEH ENGINE 2. Pull rewind starter using a quick, full arm strob Keep a firm grip on the handle. Return rop^ slowly. 3. After engine starts, move control lever gradually to "RUN" position. 6 TO STOP ENGINE 1. Move control lever to "STOP" position. See figure 8. Remove high tension wire from spark plug to prevent accidental starting while equipment is unattended. Your shredder is designed for safe, efficient operation. CARE MUST BE EXERCISED THAT HANDS AND FEET ARE KEPT AWAY FROM ALL OPENINGS. A Your shredder upper guide extension is adjustable. It may be adjusted to desired height by loosening the hand knob as shown in figure 9. Upper guide extension can be raised to close opening if hopper is not installed. Feed the material so that it slides down upper guide extension. See figure 10. UPPER GUIDE EXTENSION FIGURE 10. FEEDING MATERIAL INTO UPPER GUIDE EXTENSION Leaves and small twigs can be raked into the upper guide extension when the upper guide extension is lowered. See figure 11. CAUTION The manufacturer recommends that the operator wear safety glasses or some other suitable eye protection as it is possible for chips to be ejected out of the inlet openings while feeding material. UPPER GUIDE EXTENSION HAND KNOB FIGURE 9. UPPER GUIDE EXTENSION ADJUSTMENT. FIGURE 11. RAKING LEAVES AND TWIGS INTO UPPER GUIDE EXTENSION Bulky material, such as stalks or heavy branches, should be fed into the chip-it guide extension. See figure 12. Do not force or jam material into the chip-it guide. 7 I KEEP UPPER GUIDE EXTENSIOM UP WHEN USING CHIP-ITGyiDi: > \t ik A CAUTION Do not d...
Dieses Handbuch ist für folgende Modelle:Häcksler - 24650S (1.26 mb)