Login:
Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Anleitung Troy-Bilt, modell 071

Hersteller: Troy-Bilt
Dateigröße: 3.34 mb
Dateiname: 93cd5581-20d7-cb34-e18d-d9804ac94e26.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


See Figure 5. b. Pull spring loaded pin out on the base and align pin with the first hole (closest to the end of the tube) in the hose adapter. c. Release the pin to lock the hose in place. 3 Setting Up Your Yard Vacuum IMPORTANT Make sure the cables are routed outside the lower handle. Also, do not crimp the cables while lifting up the handles. A B Rope Guide A B Figure 6 6. a. Snap the hose handle first into the upper hose handle bracket and then into the lower hose handle bracket. See Figure 6. b. Lay hose tubing on hanger bracket next to chipper chute. Attaching The Bag 7. Grasp bag handle with one hand and slide locking rod on mounting bracket with other hand toward engine. Use the end of mounting bracket as leverage when sliding the locking rod. a. Slip bag over the rim of the discharge opening and release locking rod to secure bag in place. See Figure 7. b. Snap bag clip to the top of the lower handle. c. Place the lower straps on the bag over the top of lower handle, hooking them on the studs. See Figure 7. NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on bag handle when securing the bag or engine will not start. A B C Figure 7 3 Setting Up Your Yard Vacuum NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on bag handle when securing the bag or engine will not start. A B Figure 8 Attaching The Blower Chute (If Equipped) NOTE: The bag must be removed before installing the blower chute. 8. a. Grasp blower chute with one hand and slide locking rod on mounting bracket with other hand toward engine. Use the end of mounting bracket as leverage when sliding the locking rod. See Figure 8. b. Slip blower chute over rim of discharge opening and release locking rod to secure chute in place. c. Raise the nozzle height to the highest setting when using the blower chute. Refer to nozzle height adjustment in the Maintaining Your Yard Vacuum section on page 14. NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on the blower chute or engine will not start. 3 Setting Up Your Yard Vacuum NOTE: The bag must be removed before installing the blower chute. 10 Figure 9 Now that you have set up your yard vacuum for operation, get acquainted with its controls and features. These are described below and illustrated on this page. This knowledge will allow you to use your new equipment to its fullest potential. WARNING: The operation of any chipper shredder can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear the safety glasses provided with this unit or eye shields while operating or while performing any adjustments or repairs. Chipper Chute Allows twigs and small branches up to 1-1/2” in diameter to be fed into the impeller for chipping. See Figure 9. Drive Control Located on the underside of the upper handle, the drive control is used to engage/disengage wheels. Fully squeeze the drive control against the upper handle to engage the wheels; release to disengage. (DO NOT slip clutch). Speed Control Located on the left side of the upper handle, the speed control is used to select the forward speed of the yard vacuum. IMPORTANT: Move the speed control only when the engine is running. Changing the speed control setting with the engine off can damage the yard vacuum. Nozzle Height Adjustment Lever Used to adjust the nozzle ground clearance ranging approximately from 5/8” to 4 1/8”. See Figure 9. Throttle Control Lever (Not Shown) The throttle control lever is located on the engine. It controls the engine’s speed and stops the engine. See separate engine manual packed with unit for details. Engine Controls See the separate engine manual for the location and function of the controls on the engine. Nozzle Yard waste such as leaves or pine needles can be vacuumed up through the nozzle for shredding. 4 Operating Your Yard Vacuum WARNING The operation of any chipper shredder can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear the safety glasses provided with this unit or eye shields while operating or while performing any adjustments or repairs. Know Your Yard Vacuum Throttle Control Choke Control †Blower Chute †If Equipped Chipper Chute Bag Handle Starter Handle Oil Fill Bag Nozzle Gasoline Fill Hose Assembly Hose Handle Nozzle Height Adjustment Lever Nozzle/Hose Vac Lever Drive Control Speed Control Hose Assembly Used as an alternative to the nozzle to vacuum yard waste such as leaves or pine needles in hard to reach places. See Figure 9. Nozzle/ Hose Vac Lever The nozzle/hose vac handle is located on top of the nozzle. Use it to switch vacuum suction between the nozzle and the hose assembly. Hose Handle Used to guide hose assembly when vacuuming. Bag Handle Used to grasp bag in order to assist in attaching, removing, and emptying b...

Dieses Handbuch ist für folgende Modelle:
Häcksler - 070 (3.34 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien