Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Rover Dateigröße: 667.88 kb Dateiname: 04009134-F_ChipNShred-Australasia.pdf Unterrichtssprache:

* Do not allow processed material to build up in the discharge area. This may prevent proper discharge and can result in kickback of material through the feed opening. * Keep all guards and deflectors in place and in good working condition. * Always stand clear of the discharge area when operating this machine. * Keep your face and body away from the feed opening. * Do not overreach. Keep proper balance and footing at all times. * Do not tamper with the engine governor settings on petrol engines; the governor controls the maximum safe operating speed and protects the engine and all moving parts from damage caused by over speed. Seek authorised service if a problem exists. * Do not transport this machine while the engine is running. * If the machine becomes clogged, switch-off the engine and disconnect the spark plug lead or remove the power lead from power supply, before cleaning debris away. * Switch-off the unit before attaching or removing the mulch bag. Maintenance * When this equipment is stopped for servicing, in- spection, or storage, or to change an accessory, make sure the spark plug lead is disconnected from the spark plug, or the power cord is removed from power supply. Allow the machine to cool before making any inspections, adjustments, etc. Maintain the machine with care and keep it clean. * Store the machine out of the reach of children and where petrol vapours will not reach an open flame or spark. For extended storage periods, run the unit dry of fuel. Always allow the machine to cool before storing. iv Rover Mowers Limited Chip ‘N’ ShredTM SAFETY INSTRUCTIONS General Electrical Safety Rules 1. Avoid dangerous environments such as damp locations. 2. Do not abuse the power cord. Never pull a machine by the cord or pull the cord to disconnect it from the outlet socket. Keep the cord away from excessive heat, oil, and sharp edges. 3. Disconnect the machine when not in use, before servicing and when changing attachments. 4. Avoid accidental starting. Be sure to switch off before plugging the cord into a power outlet. 5. To prevent electrical shock, use the machine only with an extension cord suitable for outdoor use as recommended by the extension cord manufacturer; the use of suitable extension cords is extremely important for the operator’s personal safety. 6. Never use an indoor type of extension cord: these cords are designed for use with lamps and small appliances and are inadequate for high-powered machines. 7. Make sure the extension cord is in good condition. A cord with cracked or broken insulation is hazardous, particularly in the presence of moisture or combustible material. It is also important that the cord connectors be of rugged construction, in good condition, and securely attached to the outer jacket. 8. If the extension cord is damaged in any manner while operating the machine, immediately switch off the power supply and remove the extension cord from the power outlet. 9. If the supply cord is damaged it must be replaced by a CMG Service Agent or similarly qualified person in order to avoid a hazard. Electrical Supply Capacity and Fuses 1. Use only an electric circuit having adequate capacity. 2. Blowing a fuse or tripping a circuit breaker is a warning that you are overloading your machine or have too many devices in use on that circuit, or both. Determine the cause and correct it. Do not install a higher capacity fuse. 1. SPECIFICATIONS Rover Model No. 9885 (Electric) 9848 (Petrol) 9862 (Petrol) 98117 (Petrol) Engine Model No. A09189 93302 127432 G200F Power Rating 2.2 kW 2.6 kW 4.1 kW 4.1 kW Fuel Capacity 2.4 litres 4.5 litres 3.6 litres Oil Capacity 600ml 600ml 600ml Oil Grade Refer engine manufacturer's booklet Refer engine manufacturer's booklet Refer engine manufacturer's booklet Voltage 230-240 volts Current FL 9.8 amps Frequency 50Hz Phase Single No. Flails 12 12 12 12 No. Chipper Blades 1 1 1 1 Chipper Opening 71 x 71 mm 71 x 71 mm 71 x 71 mm 71 x 71 mm Weight (kg) 56 51 56 56 2. SETTING UP 2.1 Loose Parts Kit Feed hopper half LH....................................................1 Feed hopper half RH....................................................1 Hopper baffle...............................................................1 Hopper handle..............................................................1 Hopper washers............................................................4 Chipper tube assembly.................................................1 Manual.........................................................................1 Bar screen assembly.....................................................1 Screws- 10 x 3/4” pan p/head....................................12 Bolts- 1/4” x 1-1/2” unc. cuphead................................4 Nyloc nuts- 1/4” unc....................................................4 Screws- 3/16” x 5/8” mush.head..................................4 Nyloc nuts- 3/16” unc..................................................4 Washer- 3/16” x 1/2” x 2...

Herunterladen

Geben Sie zwei Ziffern: