Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Royal Sovereign Dateigröße: 1.18 mb Dateiname: Unterrichtssprache:

4. Pull the upper film around the upper idler bar to the anti-wrinkle device and stretch out the film on the upper heat shoe. 5. When the temperature reaches 80°C (176°F), the resin is melting, stick the film on the shoe. SHAFT LOWER IDLE BAR UPPER ROLL FILM SHAFT LOWER ROLL FILM GUIDING PAPER HEAT SHOE UPPER IDLE BAR LOWER FILM SHAFT LOWER IDLE BAR HEAT SHOE Picture 1 - 8 - 2. COLD FILM 1. Take out the guiding table. 2. Put the shaft of roll film in each hole exactly. 3. Set the pressure lever to the proper lamination mode.(1mm/5mm/10~13mm) 4. Pull the film around the idler bar to the Anti-wrinkle device. 5. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back. **It is to be stuck on to roll up clock wise. 6. Place the sticky part of film on the upper shoe and get ready to laminate. PAPER BACK TAKE UP DEVICE HEAT SHOE UPPER FILM SHAFT COLD FILM UPPER IDLE BAR - 9 - 1. For setting, pull the pressure lever out and turn the lever to following the indication. 5. Laminating : Mode that you can do laminate 25mic(1mil) to 250mic(10mil) 2. 10~13mm Board : Mode that you can laminate 10~13mm(1/3" to 1/2") 3. 5mm Board : Mode that you can laminate 5mm(1/4") hard board 4. 1mm hard board : Mode that you can laminate 1mm(40mil) hard board CONTROL OF ROLLER PRESSURE ***Methods of controlling pressure of the roller *** - 10 - INSTRUCTIONS FOR CONTROL PANEL You can manipulate speed and temperature with the LCD controller. We designed the LCD panel for user convenience by adopting memory working condition. ***Terms*** LCD DISPLAY BUTTON - 11 1.LCD WINDOW 1. Initial display status. It displays the last working condition when the power is turned on. 2. 3. Indicates to wait till blinking stops. Current temperature is higher or lower than the preset temperature. 4. Saving electricity status. 5. Temperature 1) Shows the preset temperature. 2) You can check the current temperature on the heat shoe by pressing T-Check button. 6. Speed *9 different speed option. (SPEED1->1.0m(3.3ft)/min. SPEED9-> 6.0m(19.7ft)/min.) 7. PRGM *9 different memory cell (address) You can memorize 9 different working conditions. when the preset temperature is reached. is displayed Blinking - 12 - 2. FUNCTIONS OF BUTTONS : Upper shoe temperature controller : Lower shoe temperature controller : Speed controller : Choose memorized working condition : . Increase temperature . Increase speed . Restore the memorized working setting : . Decrease temperature . Decrease speed . Restore the memorized working setting : Cold function : Check current temperature C/HOT T-CHECK ST/BY : Saving electricity while the machine is not being operated. UPPER LOWER ST/BYT-CHECKC/HOT MEMORY SPEED RUNSTOPREV MEANSRESET FAN UPPER LOWER SPEED MEMORY REV STOP : Reverse function RESET : Count & Length values format : Stop working FAN : Run and stop the fan RUN : Run the rollers. MEANS : Change into Count & Length Mode - 13 3.HOW TO USE BUTTONS 1. Temperature available range from 0°C (32°F) to 160°C (320°F). 2. Set temperature of upper shoe. Press upper button then you will see the LCD is blinking 6 times. Before blinking is finished, press 3. Set temperature of lower shoe. Press lower button and choose the arrow button the same way to set temperature of upper shoe. 4 Each time you press the button, it will change 1°C (2°F). If you press the button more than 2 seconds, temperature will change automatically until you press the button again. 5. Buzzer is ringing each time you press the button. 1. The operator can use 9 different lamiantion speeds. 2. Press button then speed display mode is blinking 6 times Before blinking finish, the operator can change the speed with or 3. Each time you press the button, buzzer will ring. Button & Display ***Speed controls*** ***Set the upper/ lower heat shoes*** or to set the temperature. UPPER LOWER UPPER SPEED SPEED - 14 - 1) Memorize working condition 1.Operator can memorize 9 working conditions. 2.Each time you press the button, buzzer is ringing. 3.find the condition number you are willing to memorize working condition by pressing button. 4.When you finish setting upper/lower temperature and speed, you can press the memory button. This working condition is memorized while buzzer is ringing with blinking. operation over. 2) Use the memorized working condition. 1.Operator can choose one of 9 memorized working conditions. 2.Press a working condition. The display will blink. 3.After the blinking stops, it is set the working condition you selected and shows the working condition on the display. time, memory number is blinking together, it means that working cocdition is not ***Memorizing Working condition and Using the memorized working condition*** the or to select *If you change the temperature or speed and the display shows blinking at the same set. When you memorize working condition, you have to press button. 5.When you memorize another working condition, you can do above 3 and 4 MEMORY UPPER LOWER MEMORY SPEED MEMO...

Herunterladen

Geben Sie zwei Ziffern: