Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. DO NOT USE AN EXTENSION CORD. Remove Packaging and Parts Installation Below a Countertop • Place carton on a flat surface. • Open one end of the carton and lift off the top piece. • Lift the warmer up and out of the carton. • Place the drawer on top of the shipping carton to protect the drawer front and the finished flooring. Electrical Outlet Against Rear Cabinet Wall 9" From Floor Flush With Side of Cabinet 7" Max. Electrical Outlet 16" Max. to Bottom of Block 7" From Left Side. 9" Installation Preparation Warming Drawer • Remove all packing materials and tape. • Locate package containing 4 wood screws and set aside. Parts provided: • 4 Wood Screws 1-1/2" Cabinet Top 25" Install a Solid Barrier Below a Cooktop See Note 1" Min.* 36" Countertop Height 9-1/4" Install 2x4 or 2x2 Anti-Tip Block Electrical Outlet 42" Max. From Right Side. Solid Barrier 1/4" Air Gap 23-1/2" Min. Install a Solid Barrier and a 1/4" Air Gap Above Warming Drawer • When installed, the front face of the drawer will be nearly flush with adjacent cabinetry doors. • Drawer overlaps will conceal cut edges on all sides of the opening. The rough opening for the drawer must be: – Depth - 23-1/2” min. from inside back to front of cabinet frame. – Width - 25-1/2” for 27” wide models, 28-1/2” for 30” wide models. – Height - 9-1/4”. • 5” min. above floor or 1” above toekick. 23-1/4” from floor to bottom of cutout is recommended for under countertop installation. Installation below a cooktop: Warming drawers are approved for installation below only certain specified cooktop models. See the label attached to the top of the warming drawer for approved models. A solid barrier and air gap between cooktop and warming drawer is required. See Note above. A Dim. A ZKD30 28-1/2” ZKD27 25-1/2” *Note: When installing the warming drawer below a cooktop, a solid barrier must be installed at least 1" from the lowest point of the bottom of cooktop burner box to the top of cutout. Use any solid material such as 1/4" thick plywood. Allow at least 1/4" air gap between the barrier and the top of the warming drawer. See label on top of the warming drawer for approved cooktop models. Installation below a cabinet drawer: The warming drawer may be installed beneath a cabinet drawer. In this installation, a solid barrier should be installed above the warming drawer to block access. Use any solid material such as 1/4" thick plywood. Allow at least 1/4" air gap between the barrier and the top of the warming drawer. Observe the 5" min. above the floor or 1" above the toekick minimum installation height. Note: If you are installing in frameless cabinets, it may be necessary to install 1/2” wide cleats to accept drawer mounting screws. See drawer to find exact locations of mounting screws. Side to Side Installation: Install two warming drawers in separate cutouts. Allow 2" min. between cutouts. 2" Min. Side to Side Installation Design Information Warming Drawer 23-1/2" Min. Installation Below Wall Ovens INSTALLATION BELOW A SINGLE OVEN 2x2 or 2x4 Anti-Tip Block Against Rear Wall, 9" From Floor to Bottom of Block Note: Additional clearance between cutouts may be required. Check to be sure that oven supports above the Warming Drawer location does not obstruct the required interior 23-1/2” depth and 9-1/4” height. 1" Min. Above Toekick or Adjust to Oven Installation Height A 2" Min. Allow 5/8" Overlap on All Sides B 10-1/2" 23-1/4" Inside Oven Cutout 9-1/4" 9" INSTALLATION BELOW A DOUBLE OVEN 2x2 or 2x4 Anti-Tip Block Against Rear Wall, 9" From Floor to Bottom of Block Note: Additional clearance between cutouts may be required. Check to be sure that oven supports above the Warming Drawer location does not obstruct the required interior 23-1/2” depth and 9-1/4” height. Dim. A Dim. B ZKD30 28-1/2” 30” ZKD27 25-1/2” 26-3/4” A 2" Min. Allow 5/8" Overlap on All Sides B 10-1/2" 23-1/4" 23-1/2" Min. Inside 1" Min. Above Toekick Oven Cutout 9" 9-1/4" When installed under a wall oven: Warming drawers are approved for installation below only certain specified wall oven models. See the label attached to the top of the warming drawer for approved models. • When installed, the front face of the drawer will be nearly flush with adjacent cabinetry doors. • Drawer overlaps will conceal cut edges on all sides of the opening. The rough opening for the drawer must be: – Depth – 23-1/2” min. from inside back to front of cabinet frame. – Width – 25-1/2” for 27” wide models, 28-1/2” for 30” wide models. – Height - 9-1/4”. – Allow 2” min. between oven and drawer cutouts for clearance of overlaps. Note: If you are installing in frameless cabinets, it may be necessary to install 1/2” wide cleats to accept drawer mounting screws. See drawer for mounting screw locations. Installation Warming Drawer 2"x 4" or 2"x 4" or Provide Equivalent Runners Equivalent Runners Cabinet Support 23-1/2" 22" 27" 23-1/2" 25" 30" Im...
Dieses Handbuch ist für folgende Modelle:Netzteile - ZKD910 (230.63 kb)