Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Before you begin — Read these instructions completely and carefully. IMPORTANT - Save these instructions for local inspector’s use. IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer - Be sure to leave these instructions with the Consumer. Note to Consumer - Keep these instructions with your Owner’s Manual for future reference. WARNING ATTENTION Cet appareil doit etre correctement mis a la terre. Consulter page 4. This appliance must be properly grounded. See “Electrical Supply”, page 4. If you received a damaged warming drawer, you should immediately contact your dealer or builder. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Use & Care Guide for warranty information. • Use this appliance only for its intended purpose. Check with local utilities for electrical codes that apply in your area. Local codes vary. Installation electrical connections and grounding must comply with applicable codes. In the absence of local codes, the drawer should be installed in accordance with National Electrical Code ANSI/NFPA 70-1990 or latest edition. WARNING: ANTI-TIP PRECAUTIONS An anti-tip brace must be installed to prevent the drawer from tipping forward when opened and loaded. Failure to do so could result in personal injury. PRECAUTIONS CONTRE LE BASCULEMENT Pour eviter les blessures, il faut installer une patte de retenue pour empecher le tiroir de basculer quand il est ouvert et plein. For Monogram local service in your area, 1-800-444-1845. For Monogram service in Canada, call 1-888-880-3030. For Monogram Parts and Accessories, call 1-800-626-2002. Design Information Contents Models Available.................................................................................................................................. 3 Product Dimensions ............................................................................................................................ 3 Accessories ........................................................................................................................................... 3 Tools and Materials Required ............................................................................................................ 3 Installation Preparation Advance Planning ............................................................................................................................... 4 Grounding the Appliance................................................................................................................... 4 Remove the Packaging and Parts ....................................................................................................... 5 Installation Below a Countertop ........................................................................................................ 5 Installation Below Wall Ovens ............................................................................................................ 6 Installation Step 1: Provide Cabinet Support and Anti-Tip Bracket ................................................................... 7 Step 2: Install Warming Drawer ......................................................................................................... 7 26" Including Handle 23-1/4" A 10-1/2"9" 1" Drawer Open 27" 23-1/4" A 10-1/2"9" 1" Drawer Open 27" Dimension A ZTD910 30” ZKD910 26-3/4” ZXD27B, ZXD30B – This kit provides for the Accessories installation of a custom front panel on 27” and 30" black and white wide models. Note: The original drawer front will be removed and discarded when this kit is used. The tubular handle can be reinstalled onto the custom panel with longer screws (not provided). Or, the original handle can be replaced with a custom handle of your choice.(Handle is not supplied.) Choose a custom handle to match or complement cabinetry hardware. Warming Drawer ZTD910 The warming drawers may be installed Models 30” Wide model directly into a wall or wall oven cabinetry, Available ZKD910 or below a countertop. 27” Wide model Product Dimensions JXPN1 – Warming drawer pan kit. This kit includes supports and a set of 5 pans which fit into 27" and 30" models. JXPN2 – Warming drawer pan kit. This kit includes supports and a set of 3 pans which fit into 27" and 30" models. Tools and Materials Required • Wood screws and adhesive or other hardware for installing runners or shelf to support warmer drawer. • 2 x 4 or 2 x 2 lumber for runners • 2 x 4 or 2 x 2 wood block for anti-tip security • Saw • Level • Drill and 1/16” bit • Phillips screwdriver Runners must be level, rigidly mounted and capable of supporting 150 pounds. Design Information Advance Planning Grounding the Appliance • The drawer may be installed below a countertop, a cooktop, a single or double oven and side by side using 2 drawers. • The warming drawer can be installed below approved cooktops. Allow 2" min. clearance from ...
Dieses Handbuch ist für folgende Modelle:Netzteile - ZTD910 (230.63 kb)