Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Our designated maximum climbing height for this device is 63.5 mm/ 2.5 inches. To safely mount a curb, please follow the instruction below: STEP 1 Set the Maximum Speed Indicator at 3 (recommended) by adjusting the Speed Increase / Decrease Button (Fig.14). STEP 2 Approach the curb from a comfortable distance, and push the joystick all the way forward. Fig. 8a ~12~ GMP ISO9001 ISO14001 ISO13485 CERTIFIED PREPARATION FOR USE NOTE: Before using the Powerchair for the first time, be sure the batteries have been connected. Charge the Powerchair for at least 6-8 hours prior to first time use. NOTE! Maximum efficiency can only be achieved with sufficient battery power and adequate run-up distance. WARNING! Be aware that the angle of incidence should be approached around 90° to ensure safety and stability. PROGRAMMABLE CONTROLLER WIZZ (888WNL-11), STREAMER (888WAB-11, 888WB-11, 888WSB-11), JETSTREAM-L (888WAL-11), JETSTREAM-M (888WAM-11) Powerchairs have programmable controllers. For more information regarding the programming parameters for the programmable Powerchair controller please contact your provider. Note: WIZZ (888WNL-10), STREAMER (888WAB-10, 888WB-10, 888WSB-10), JETSTREAM-L (888WAL-10), JETSTREAM-M (888WAM-10), are non-programmable Powerchairs. ~13~ GMP ISO9001 ISO14001 ISO13485 CERTIFIED ADJUSTMENT PROCEDURES FOOTREST ADJUSTMENTS (Fig. 9) STREAMER (888-WB/WAB/WSB) WIZZ (WNL) Release the lock nut and adjust the bolt under the footrest (3) to adjust the Fig. 9 (2) (3) (1) LENGTH Pull out the safety pin (1) from the first hole in the footrest slide tube (2), adjust the footrest slide tube and refit the safety pin in the hole at the desired length. ANGLE footrest angle. When the angle desired is reached, re-tighten the lock nut and bolt. ARM ADJUSTMENTS (Fig.10) STREAMER (888-WB/WAB/WSB) WIZZ (888-WNL) ANGLE Pull up on the end of the armrests and they will flip back up allowing easy transfer in and out of the seat. Under the armrest there is a bolt and lock nut (1) that can be adjusted up or down to change the angle of the armrest. LENGTH (1) (3) Fig. 10 (2) Located under each armrest is a hand knob (2). By turning counter-clockwise to release, the armrest can be extended and reset in position by re-tightening the hand knob. HEIGHT Below the armrest on the down supporting tube there is a screw and lock nut (3) that can be allowed for adjustments. Two aligned hex screws prevent any loose play. WIDTH Beneath the rear of the seat there are two hand knobs, one on each side. Release the hand knob and slide each arm assembly outward. Re-tighten the hand knob when in the desired position. ~14~ GMP ISO9001 ISO14001 ISO13485 CERTIFIED ADJUSTMENT PROCEDURES FOOTREST ADJUSTMENTS (Fig. 11) JETSTREAM-L/M (888-WAL/WAM) LENGTH Pull out the safety pin (1) from the first hole in the footrest slide tube (2), adjust the footrest slide tube and refit the safety pin in the hole at the desired length. ANGLE Release the lock nut and adjust the bolt under the footrest (3) to adjust the footrest angle. When the angle desired is reached, re-tighten the lock nut and bolt. ARM ADJUSTMENTS (Fig.12) JETSTREAM-L/M (888-WAL/WAM) Fig. 11 (1) (2) (3) ANGLE Pull up on the end of the armrests and they will flip back up allowing easy transfer in and out of the seat. Under the armrest there is a bolt and lock nut (1) that can be adjusted up or down to change the angle of the armrest. LENGTH (1) (3) Fig. 12 (2) Located under the armrest controller bracket is a hand knob (2). By turning counter-clockwise to release, the controller bracket can be extended and reset in position by re-tightening the hand knob. HEIGHT Below the armrest on the down supporting tube there is a lever (3) that can be pushed down for armrest height adjustments. WIDTH Beneath the rear of the seat there are two hand knobs, one on each side. Release the hand knob and slide each arm assembly outward. Re-tighten the hand knob when in the desired position. ~15~ GMP ISO9001 ISO14001 ISO13485 CERTIFIED ADJUSTMENT PROCEDURES JOYSTICK CONVERSION (right to left or left to right) Beneath each of the arm pads there is a hand knob [Fig.10 (2)] used to adjust the length of the arm pad and secure the arm pad to the arm rest assembly. Remove the hand knob completely and slide off the arm pad. You can now exchange the joystick controller from one side to the other. SEAT HEIGHT ADJUSTMENTS (Fig.13) WIZZ (888WNL): The four seat supporting posts under the seat have three height adjustment holes each. By fitting the retaining pin in any one of the holes, three heights can be achieved. STREAMER (888WB/WAB/WSB): The tube receiving seat stem has three (STREAMER 888WB/WAB) or two (STREAMER 888WSB) height adjustment holes. By fitting a steel bolt in any one of the holes, the selected heights can be achieved. JETSTREAM-L/M (888WAL/WAM): The front and rear tube receiving posts have three height adjustment holes. By fitting a steel bolt in any one of the holes, the selected heights can be achieved. S...
Dieses Handbuch ist für folgende Modelle:Rollstühle - ISO13485 (935.91 kb)
Rollstühle - ISO9001 (935.91 kb)