Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Philips Dateigröße: 617.86 kb Dateiname: dc1010_12_dfu_eng.pdf Unterrichtssprache:

– Perchlorate Material-special handling may apply. See perchlorate. • Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst: • Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not try to mix old batteries with the new ones. • Remove the batteries if the set is not to be used for a long time. Using AC Mains 1 Check if the power/mains voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center. 2 Connect the power cord to the AC MAINS inlet and the wall socket.The mains lead is now connected and ready for use. 3 To switch the set off completely, withdraw the power cord from the wall socket. 4 Install the unit near the AC outlet and where the AC power plug can be easily reached. • Disconnect the mains lead from the wall socket to protect your set during heavy thunderstorms. Children could seriously injure themselves as the free end of the cable may still be live if only the connector is removed from the MAINS socket at the back of the unit. The type plate is located on the bottom of the set. Helpful hints: –To avoid unnecessary energy consumption, always adjust the source selector to OFF after using the set. Basic Operation/Radio CD Player Basic operation 1 To select your sound source, adjust the source selector to: TUNER,AUX, CD, iPod, or OFF. 2 To switch off the set, adjust the source selector to OFF position and check the cassette keys are released. Helpful hints: In tuner mode, if you connect a 3.5 mm aux-in cable, the source changes to AUX automatically. Adjusting volume Adjust the volume with the VOLUME control. Radio reception 1 Adjust the source selector to TUNER. 2 Adjust BAND to FM or AM as your desired band. 3 Turn TUNING to tune to a station. • For FM, extend and turn the telescopic antenna for best reception. Reduce its length if the signal is too strong. • For AM, the set uses a built-in antenna. Direct this antenna for best reception by turning the whole set. 4 To switch off the radio, adjust the source selector to OFF position. Playing a CD This CD player plays Audio Discs including CD-Recordables and CD-Rewritable. • MP3 CD-ROMs, CD-I, CDV,VCD, DVD or computer CDs are not possible for playback on this set. IMPORTANT! • CDs encoded with copyright protection technologies by some record companies may be unplayable by this product. 1 Adjust the source selector to CD. 2 Open the disc door. 3 Insert a CD with the printed side facing up and press the CD door gently to close. . Display shows --and later, the total number of tracks. (See 2, 3) 4 Press 2; on the set to start playback. .Display: 2 and the current track number. (See 4) 5 To pause playback press 2;.To resume playback, press 2; again. 6 To stop CD play, press 9. Helpful hints: CD play will also stop when: – you open the CD compartment; – you select TUNER,AUX, or OFF sound source; – the CD has reached the end of playback. Selecting a different track • Press 5 or 6 once or repeatedly until the desired track number appears in the display. • In the stop/pause position, press 2; to start playback. CD Player Finding a passage within a track 1 During playback, press and hold down 5/ 6. . The CD is played at high speed and low volume. 2 When you recognize the passage you want release 5/ 6. . Normal playback resumes. Helpful hints: – When your searching reaches the end of the last track, the CD goes to stop mode. Programming track numbers You may store up to 20 tracks in the desired sequence. If you like, store any track more than once. 1 In the stop position, press PROG to activate programming. . Display: PROG and 00 flash (see 5). 2 Press 5 or 6 to select your desired track number. . Display: PROG and your desired track number flash. 3 Press PROG to store the desired track number. . Display: PROG and 00 flash for you to program the next track. 4 Repeat steps 2 to 3 to select and store all desired tracks in this way. 5 To play your program, press 2;. . Display: PROG flashes during program playback. Helpful hints : – If you try to store more than 20 tracks, no track can be selected and the display will show flashing --. To review a program • In the stop position, press and hold PROG for two seconds to see your stored track numbers. Erasing a program You can erase the contents of the memory by: – in the stop position, press PROG to enter program mode, and then press 9; – Selecting TUNER,AUX, or OFF sound source; – opening the CD door. .Display: PROG disappears. Different play mode REPEAT You can play the current track or the whole disc repeatedly, and combine REPEAT modes with PROGRAM. REPEAT – plays the current track continuously. REPEAT ALL– repeats the entire CD/program. 1 To select play mode, press REPEAT once or more. . The display shows selected mode. 2...

Herunterladen

Geben Sie zwei Ziffern: