Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
SECTION 8. TROUBLE SHOOTING If your Power Chair will not go, follow this checklist 1. Check that the lights on control box are illuminated. 2. If there are no lights on controller, check that all leads/plugs, which connect to controller, are pushed in properly. 3. Check that the motor cables are properly connected 4. Check all battery wiring is connected. 5. Check that battery box connector is plugged in. 6. Check circuit breaker located on the battery box lid. The circuit breaker will trip when the wheelchair is stalled for a prolonged period or if a major fault has occurred. If circuit breaker continually trips for no apparent reason, cease use and contact nearest Glide Products service agent. Important: Allow 60 seconds before resetting circuit breaker. 7. If you still have problems after reviewing the above checklist, please contact your nearest Glide Rehabilitation Products Agent or Glide Rehabilitation Products direct. SECTION 9. PENNY & GILES PILOT + SERIES CONTROLLER Figure 3. Penny & Giles Controller CONTROLS On/Off Push button This is a green pushbutton switch fitted in front of the joystick, which turns the controller On and Off. Do not use this switch to stop the wheelchair except in an emergency. TruCharge Battery Gauge This is a 10 segment illuminated display which indicates if the controller is turned On and also gives the status of the battery, the controller and the wheelchair electrical system. Red, Yellow and Green bars illuminated: Battery charged; controller and electrical system OK. Red and Yellow bars illuminated: Charge battery if possible, controller and electrical system OK. Red bars only illuminated or Slow Flash: Charge battery as soon as possible; controller and electrical system OK. Rapid Flash of bars: Indicates a fault in the controller or electrical system. See below for fault diagnostics. Ripple Up and Down of bars: Joystick displaced at Turn On. Ensure joystick is in central position, Turn off and On. Joystick Controls the speed and direction of the wheelchair. Push the joystick in the direction that you wish to go. The further you push it, the faster the speed. Releasing the joystick stops the wheelchair automatically. Maximum Speed/Profile Indicator This is a gauge which shows the maximum speed setting for the wheelchair or, if the control system is programmed for a drive profile, the selected drive profile. To change speed/profile you must press the MODE button. If the mode button is pressed while you are driving the maximum speed setting will be increased by one step. Each successive operation of the mode button will increase the setting. There are five settings and the system will toggle to the next setting each time the mode button is pressed while driving. E.g 1-5 and 5-1 If the MODE button is pressed when the joystick is centred – when chair is stationary – the control system operation mode will be changed. There are three modes – drive, speed adjustment and actuator adjustment. 1. To adjust speed when in this mode – The maximum speed can be adjusted by left or right movements of the joystick. Left will decrease the speed, right will increase it. Forward or reverse movements of the joystick will take you back into drive mode. 2. When the control system is in this mode the actuator indicator will be illuminated. The section of the wheelchair symbol that is illuminated shows the actuator that is selected for adjustment. To change the selected actuator move the joystick left or right. To make adjustments to the selected actuator move the joystick forwards or backwards. Horn Button Horn will sound for as long as button is pressed Charger Socket This 3 pin socket is used to connect your battery charger and also to programme/re – programme controller using the PP1 programmer, should this be necessary. PENNY & GILES FAULT TREE Figure 4. Penny & Giles Fault Tree SECTION 10. DYNAMIC CONTROLS CONTROLLER Figure 5. Dynamic Controller CONTROLS DX – G90A REMOTES On/Off Button – This is a white pad located in front of joystick control knob. It is also identified by having 1/0 printed on it. Mode/Program Select Button This is a Light Blue pad located to the left of the On/Off pad. Each press of the mode button will increment the drive profile, up to the maximum configured value, and then back to profile 1. The current profile will be displayed in the drive display. Actuator/ASK (Accessory Shortcut Key) Button This is a Red pad located to the right of the On/Off pad. A press of this button will navigate you to last used accessory function, e.g. actuator control. If you are already in accessory mode, a press of ASK, will navigate you to next available accessory function, e.g. lights or ECU. To change to different actuators simply move the joystick left or right to take you to the next function, e.g. tilt or recline. Then move joystick forward or back to operate actuator, e.g. up or down. To return to driving, simply press the Blue mode button. Horn Button Pressing the Horn button wi...
Dieses Handbuch ist für folgende Modelle:Rollstühle - 6 Series (1.61 mb)