Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Enerco Dateigröße: 6.32 mb Dateiname: Unterrichtssprache:

2. Mark screw locations on wall (see figure 7). 3. Remove tape and mount bracket from wall. Figure 7 Attaching to Wall Stud: For attaching mounting bracket to wall studs 1. Drill holes at marked locations using 9/64” drill bit. 2. Place mounting bracket onto wall. Line up holes on each end of bracket with hole drilled in wall. 3. Insert mounting screws through bracket and into wall studs. 4. Tighten screws until mounting bracket is firmly fastened to wall studs. Attaching to Wall using Anchor: For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry) Note: Wall anchors, mounting screws, and spacer are in hardware package. The hardware package is provided with heater. 36” min. from ceiling 6” Min from adjoining walls Left Side Right Side Floor 2” min. to top surface of carpet, tile or other combustible material 6-1/2” Min. 10,000 BTU 10-1/4” min 20,000-30,000 BTU Adjoining Wall 16” (Lg) 12-9/64” (Sm) 17-1/2” Min. Mark mounting hole locations and drill holes where indicated. Allow for minimum clearances Mounting Bracket 1. Drill holes at marked locations using 5/16” drill bit. For solid walls (concrete or masonry), drill at least 1” deep. 2. Fold wall anchor as shown in figure 8 below. Figure 8. 3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall. 4. For thin walls (1/2” or less) insert red key into wall anchor. 5. Place mounting bracket onto wall. Line up holes on each end of bracket with wall anchors. 6. Insert mounting screws through bracket and into wall anchors. 7. Tighten screws until mounting bracket is firmly fastened to wall. Placing Heater on Mounting Bracket 1. Locate two horizontal slots on back pane of heater (see figure 9). 2. Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket. Figure 9. Installing Bottom Mounting Screws 1. Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see figure 10). Figure 10 2. Mark screws locations on wall. 3. Remove heater from mounting bracket. 4. If installing bottom mounting screw into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching to Wall using Anchor. If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64” drill bit. 5. Re-place heater onto mounting bracket. 6. Place spacers between bottom mounting holes and wall anchor or drilled hole. 7. Hold spacer in place with one hand. With the other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole. 8. Tighten both screws until heater is firmly secured to wall. Do not over tighten. Note: Do not re-place front panel at this time. Re- place front panel after making gas connections and checking for leaks. FLOOR MOUNTING AWAY FROM WALL: Figure 11 Installing Support Feet (see figure 11) 1. Lay heater onto table on its back with bottom edge overhanging table edge. 2. Securely attach feet to bottom of heater using 2 – self-tapping screws each. Note: Feet should have long end going out the front of heater, and the edge coinciding with side of heater. If feet overhang side of the heater, switch leg location. 3. Place heater on non-combustible surface (see Locating Heater above) before proceeding with gas connection. If this will be a permanent location, heater may be locked into position using anchoring holes in mounting feet. Note: Use of floor mounting feet will require you to use a 3/8 NPT street elbow to make gas connection. CONNECTING TO GAS SUPPLY WARNING: A qualified service person must connect heater to gas supply. Follow all local codes. Horizontal Slots Mounting Bracket mounted to wall WARNING: This appliance requires a 3/8” NPT (National Pipe Thread) inlet connection to the pressure regulator. Use of floor mounting feet will require you to use a 3/8 NPT street elbow to make gas connection. CAUTION: Never connect heater to private (non-utility) gas well. This gas is commonly known as well-head gas. IMPORTANT: Check your gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 14 inches of water. If gas line pressure is higher, heater regulator damage could occur. CAUTION: Use only new black iron or steel pipe. Internally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of larger enough diameter to allow proper gas volume to heater. If pipe is too small, undue loss of pressure will occur. Installation must include an equipment shutoff valve, union and plugged 1/8” NPT tap. Locate NPT tap within reach of test gauge hookup. NPT tap must be upstream from heater (see figure 12). Figure 12 *A CSA/AGA certified equipment shutoff valve with 1/8” NPT tap is an acceptable alternative to test gauge connection. Purchase the CSA/AGA certified equipment shutoff valve from your dealer. See Accessories, page 17. IMPORTANT: Install an equipment shutoff val...

Herunterladen

Geben Sie zwei Ziffern: