Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Homelite Dateigröße: 553.34 kb Dateiname: Unterrichtssprache:

The instructions and parts list for the dump cart will be found packaged with the car . Assembly Mounting the Vacuum Collector 1. Install the drive pulley on the tractor PTO shaft using a 3/16 x 3/16 x 1" key. Secure the pulley with the set screw provided. Install the three belt stops on the tractor frame. The 7/16-14x1-1/4” capscrew provided for the upper belt stop, replaces the original cap screw on the tractor (Figure 1). 2. Install the lift shaft on the rear of the tractor using the two set collars. Secure the set collars with the two 5/16-18 set screws provided (Figure 2). 3. Place the hooks on the upper arms of the support assembly over the lift shaft. Align the holes in the lower arm of the support assembly with the holes in the tractor frame. Secure with two pins and two quick pins. (Figure 2) 4. Move the PTO lever forward to the disengaged position. Install the drive belt over the drive pulley. Align the drive pulley with the pulleys in the belt drive cover. Check to insure that the belt is properly seated in the four pulleys. Adjust the belt stops as shown (Figure 3). 5. Attach the deflector to the blower housing with two 3/8" self tapping screws (Figure 4). 6. Place the 6" diameter hose over the deflector and blower housing and secure with the smaller of the hose clamps using one 1/4-20 x 2" machine screw, lockwasher and hex nut (Figure 4). 7. Mount one end of the 7” hose to the hose flange using one of the larger hose clamps and one 1/4-20 x 2" machine screw, lockwasher and hex nut (Figure 4). 8. Slide the hose flange into the slots in the blower housing (Figure 4). 9. Install the hose extension in the other end of the 7" hose. Secure with the other large hose clamp and one 1/4-20 x 2" machine screw, lockwasher and hex nut (Figure 5). ADAPTER HOUSING ■NUT ASSEMBLY DEFLECTOR GUARD see note: PIN FITS HERE CARRIAGE BOLTS' note: 1973 mowers only. MOWER DECK Figure 5 NOTE: 1973 mowers 42" and 48" are equipped with a deflector shield. To mount the adapter on these mowers, raise the mower to full height and remove the two carriage bolts holding the deflector in the position. Lift the deflector to a vertical position and install the adapter following assembly instructions No. 10 and No. 11. After this is done, fold the deflector shield down so that it rests on top of the adapter housing (Figure 6). 10. Raise the mower to full height. Install the two 3/8-16 x 1" carriage bolts through the holes in the mower deck from underneath. Secure with two 3/8" lock washers and two 3/8-16 hex nuts (Figure 6). 11. Insert the pin on the rear edge of the vacuum collector adapter through the hole in the rear edge of the mower deck. Locate the two large holes in the top of the adapter over the carriage bolts in the mower deck. Secure with the two nut assemblies (Figure 6). 12. Slide the hose extension over the adapter discharge pipe (Figure 5). Mounting the High Capacity and Low Profile Trailer Frames and Covers There are two covers available for the HOME LITE dump cart for use with the HOME LITE vacuum collector system. These are the low profile trailer frame and cover and the high capacity trailer frame and cover. Both covers come preassembled to their frames. The low profile trailer frame and cover is assembled as follows: 4 1. Install the front stops on the cover front frame (the end with the hose sleeve). The special studs are inserted from the inside (Figure 7). The high capacity trailer frame and cover is assembled to the dump cart as follows: 1. Remove the tailgate from the dumpcart. 2. Lay the assembly on the cart with the canvas side flaps inside the cart.) Engage the front stops over the box front edge, then pull the rear latch down and hook it under the box rear edge (Figure 8). 3. Place the 6" diameter hose in the cover sleeve and secure by tightening the strap in the sleeve. Figure 9 5 2. Install^ the front catch using a 3/8-16 x 1” capscrew, flatwasher and locknut. Tighten the locknut so that it will hold securely but still allow the catch to pivot. (Figure 9). 3. Unfold the canvas and frame assembly so that the front and rear uprights are in a vertical position. Align the side "Z" bars with the cart side wall upper edges and slide the assembly forward onto the cart (Figure 10). Be sure that the front of the cover frame is toward the front of the cart. Turn the front catch down over the front edge of the cart. 4. Secure the four crossbrace tubes with the hardware attached (Figure 9)., 6. Engage the upper doorframe side caps crews in the upper hanger brackets and push the bottom edge into place in the box bed. Engage the rear latches to the lower door frame side capscrews (Figure 11). 7. Place the 6" diameter hose in the cover sleeve and tighten the strap in the sleeve (Figure 9). 8. Secure one end of the spring to the strap in the cover sleeve by knotting the en...

Herunterladen

Geben Sie zwei Ziffern: