Stimmen - 3, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Fire could result. •Disengage blade and stop engine prior to clearing grass from either the discharge chute or grass catcher components. •Do not operate the mower with the grass catching attachment partially removed. Operator or bystanders could be injured by thrown objects. •Keep all attachment bolts tight. •Important: Do Not leave clippings in the bags while the mower is stored. Damp grass clippings are a fire hazard if left in the bag. 33 OPERATION INSTRUCTIONS SIDE DISCHARGE OF THE CLIPPINGS: In order to achieve optimum performance when side discharging the grass clippings, please read and follow the tips listed below. Additional information can be found in the Troubleshooting guide. CAUTION To avoid personal injury, be sure that the deflector is properly installed on the discharge chute. 1. Set engine speed control to the wide open or full setting. 2. Do not attempt to cut grass when it is wet. Wet grass will clog the underside of the deck and discharge area. 3. If the grass is tall, place the mower deck cut height lever in the top or second notch. “Initially” overlap cutting swaths instead of a full swath with each pass. Some applications may require a second cutting. 4. Keep the underside of the mower deck clean. Frequent removal of dried grass and dirt will allow the clippings to discharge correctly. Never, under any circumstances, should you place hands or feet under the mower deck or in the chute while blades or impeller are still turning. 5.Maintain sharp blade(s) throughout the cutting season. 34 OPERATION INSTRUCTIONS GRASS HEIGHT & CUTTING SUGGESTIONS: Do not attempt to cut grass when it is wet. If the grass is tall, place the mower deck cut height lever in the top or second notch. “Initially” overlap cutting swaths instead of a full swath with each pass. Some applications may require a second cutting. Keep the underside of the mower deck clean. Maintain sharp blades throughout the cutting season. As a rule of thumb, never cut off more than 1/3 of the total grass blade length. Correct mowing height can reduce weeds and disease by 50% to 80%. The following grass cut heights are based on adequate moisture conditions and normal thatch build-up in a healthy lawn. Some locations and applications may require slightly different cut heights. If in doubt, consult your local lawn professional for assistance. Grass Types Best Cut Heights Bermudagrass 1 - 2” Bluegrass 2 - 3” Buffalograss 11/2 -3” Ryegrass 2 - 3” Tall Fescue 3-31/2” Zoysiagrass 1 - 3” 35 CARE AND MAINTENANCE WARNING Failure to observe the following instructions may result in personal injury. Before performing any maintenance, turn off engine, allow to cool & remove key. Use extreme care when working on machinery. Do not wear watch or jewelry. Do not wear loose fitting clothes, and observe all common safety practices with tools. MAINTENANCE SCHEDULE •Check deck serpentine belt..................................after 20 hours break-in •Check crankcase oil level..............................................before each use •Clean grass & debris from muffler & manifold area............before each use •Check air intake screen...................................................after each use •Clean grass under deck...................................................after each use •Check tire pressure.........................................................every 10 hours •Inspect blades for sharpness............................................every 10 hours •Clean air filter element.....................................................every 25 hours •Grease all zerks.............................................................every 50 hours •Check all belts................................................................every 50 hours •Change engine crankcase oil.......................................(5 hours break-in) every 50 hours •Change engine oil filter....................................................every 50 hours •Replace air filter element..............................annually or every 100 hours 36 CARE AND MAINTENANCE CUTTER BLADE MAINTENANCE: CAUTION Stop engine and remove ignition key for safety. Wear heavy, thick gloves when holding onto cutter blade, avoid the sharp edge of the blade. Check sharpness of mower blades after every 10 hours of operation. Observe proper blade position prior to removal. 1. Safely raise front of mower. 2. Hold or block blade from turning. 3. Loosen blade bolt and remove blade. 4. When replacing blade, tighten blade bolt securely. Refer to diagram. Be sure blade is centered on pilot before tightening nut to 60 ft. lbs. Blades should be discarded when worn excessively. DANGEROUS! DO NOT USE BLADE IN THIS CONDITION!New Blade When notch starts, discard blade 37 CARE AND MAINTENANCE ENGINE: For complete maintenance and operating information of the engine, please refer to the maintenance instructions furnished by the engine manufacturer included in your Zero Turn Radius mower information packet. Battery contains su...