Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Remove the belt guard. 3. Remove the front PTO drive belt from the double drive pulley, and replace with a new belt. 4. Install the double drive pulley belt guard in the same position noted in step 1. Secure the belt guard in proper position using the washer and bolt. When the PTO drive belt has been replaced, the mower deck reinstalled onto the tractor, and the front PTO drive belt positioned onto the engine drive pulley and the idler pulley, refer to "DOUBLE DRIVE PULLEY BELT GUARD ADJUSTMENT" on page 27 to check for proper adjustment. 36 SECTION VII. MOWING STARTING THE MOWER ■^NOTE If the operator leaves the seat while the PTO engagement lever is in the "ON" position, or the unit is shifted into reverse when the PTO engagement lever is in the "ON" position, the engine will automatically shut off. To restart the engine, shift into neutral ”N", move the PTO engagement lever to the "OFF" position, and restart the engine while seated. While the operator is seated, and the engine running, move the throttle lever to the "FAST” position. Push the PTO engagement lever forward to the "ON" position. The mower deck should normally be operated with the throttle lever in the "FAST" position. STOPPING THE MOWER Move the power take-off (PTO) engagement lever to the "OFF" position and reduce engine speed. CUTTING HEIGHT The mower can be set in multiple positions. Proceed as follows: 1. Pull the lift handle back slightly and depress the button on the top of the lift handle. 2. Release the button when the desired mower position is obtained. 11^ NOTE To return the mower to a specific position, note position of the lift lever indicator in relation to the lever position decal before raising or lowering the mower. MOWING A WARNING To avoid possible injury, do not allow anyone in the area opposite the discharge chute while mowing. Although the area has been supposedly cleared of foreign objects, small objects may be discharged by the mower. A WARNING Never direct discharge of material toward bystanders or allow anyone near the machine while in operation. For best results it is recommended that the first two laps should be cut with the discharge thrown towards the center. After the first two laps, reverse the direction to throw the discharge to the outside for the balance of cutting. This will give a better appearance to the lawn. Do not cut the grass too short, as the mower will tend to scalp the grass. Short grass invites weed growth and yellows quickly iri dry weather. Mowing should be done with the engine at full throttle. Do not mow at high ground speed. During certain times of the year and under some conditions, the mower may leave streaks of uncut material. Streaking may occur when attempting to mow heavy weeds and tall grass. Under these conditions it may be necessary to go back over the cut area a second time to get a clean cut. The following practices will help eliminate streaking: 1. Mow the area more often so the grass doesn’t get too tall and heavy. 2. Operate the tractor at full throttle and lower forward speeds. 3. Keep the blades sharp and replace blades when worn. 4. Follow the mowing procedure shown in Figure 59. Figure 59 37 OPTIONAL EQUIPMENT AND ACCESSORIES When you purchased your tractor, you probably had it completely equipped for your particular needs at the time. However, later you may wish to obtain optional equipment or accessories. These items and other allied equipment can be purchased from, and installed by, your authorized dealer. The tractor is used for so many different types of work, and because it is called on to operate under so many different conditions, a variety of equipment is available to adapt it to the requirements of the user. Refer to equipment catalog. 38 MAINTENANCE CHART Operation to be performed Before each use 10 hours or once a month 25 hours three times a season 50 hours 100 hours or yearly Before storage Clean grille (front & backside) & engine inlet air screen More often under dirty conditions X Check engine oil level X Fill fuel tank X Cylinder head cleaning u .eaded fuel — 100 - 200 hours nleaded fuel — 200 - 300 hours Change engine oil After first 5 hours More often under dirty conditions X Check battery electrolyte level X Grease front axle pivot bolt X X Lubricate steering knuckles (2) and steering arm X Retorque rear and front wheel bolts After first 10 hours X X Lubricate brake shaft X Clean cooling fins & external surfaces X Service air cleaner More often under dirty conditions Check spark plugs X X Lubricate speed control linkage cam plates (1020 Tractor) X Check and regrease front wheel bearings X X Drain fuel X Pivot bar adjustment bolt X PTO clutch bracket X Steering gear X Deck spindles X NOTE Maintenance information for optional equipment may be found in the manual which is included with the specific piece ...
Dieses Handbuch ist für folgende Modelle:Handrasenmäher - 1020 (4.6 mb)