Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Hersteller: Poulan Dateigröße: 704.5 kb Dateiname: Unterrichtssprache:

UNPACKING INSTRUCTIONS • Remove all parts and packing materials from carton. • Check carton contents against list. Be sure all parts are there. PARTS IDEN TI FI CATION CARTON CON TENTS: (2) Container Tops (1) Cover Assembly (2) Container Bottoms (1) Support As sem bly (1) Upper Chute (1) Owner's Manual (1) Lower Chute COVER WARNING Do not operate mower unless container isproperlyissubject towear anddetierioration. Checkbagfrequently. Replacewhencrackedor damaged. Useonly arecommended replacement container. WARNING Do not operate mowerunlesscontainer isproperlyissubject to wear anddetierioration. Check bagfrequently. Replacewhencrackedor damaged. Use only a recommended replacement container. 02084 GRASS CATCHER CONTAINERS LOWER CHUTE CHUTE LATCH UPPER CHUTE FULL BAGGER INDICATOR NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 4 5 02645 02643 BAGGER SUPPORT ASSEMBLY (See Fig. 1A) 1. Your tractor already has four (4) shoulder bolts installed on the rear drawbar, simply hang the support assembly on the bolts. 1 PULL OUT ON STOP BRACKET TO REMOVE SUPPORT ASSEMBLY TO REMOVE THE SUPPORT ASSEMBLY (See Fig. 2) 1. Pull outward on the stop bracket enough to allow support assembly to be lifted up and away from drawbar. SHOULDER BOLTS FIG. 1A 2 FIG. 2 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 2) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor as shown. 2. Lift and rotate cover to align cover bracket with support assembly. 3. Slide cover assembly down onto the support assembly. 02646 COVER ASSEMBLY SUPPORT ASSEMBLY SUPPORT ASSEMBLY ASSEMBLY FIG. 1B 6 WARNING Donotoperatemowerunlesscontainerisproperlyis subjectto wearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonly arecommendedreplacementcontainer. WARNING 02082 CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side fi rst with warning to outside of unit. Install other container to right side. NOTE: Right con tain er should always over lap left con tain er at center sup port. 2. Close cover and lock latch handle over center sup port tube. 4 CENTER SUPPORT TUBE COVER LATCH HANDLE CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING Fig. 4 3 CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunless containerisprope rlyissubjecttowear anddetierioration.Checkbagfrequ ently.Replacewhencrackedordamaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 3 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF 7 02098 02099 UPPER CHUTE (See Figs. 6A & 6B) 1. Lower mower deck to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage full bagger in di ca tor. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with align ment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. 6 FULL BAGGER HANDLE INDICATOR UPPER CHUTE COVER LOWER CHUTE Fig. 6A BOSSES LATCH PIN ALIGNMENT SLOTS RUBBER LATCH Fig. 6B LEVEL MOWER DECK Be sure deck is properly leveled for best mower per for - mance. See your tractors owner's manual for in struc - tions. 7 02924 ATTACH LOWER CHUTE (See Fig. 5) 1. Raise and hold defl ector shield in upright position. 2. Place slot in lower chute over tab on mower deck and position lower chute over deck opening as shown. 3. Hook rear latch into fl ange hole on back of mower deck. 4. Hook front latch into tab hole on front of mower deck. 5 CAUTION: Do not remove defl ector shield from mower. Raise and hold shield when attaching lower chute and allow it to rest on chute while in operation. REAR LATCH FRONT...

Herunterladen

Geben Sie zwei Ziffern: