Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Tighten securely. Figure 10. Install Blower Mount Plate A. Blower Mount Plate D. 5/16” x 3/4” Bolt (3) B. 5/16” Self-Tap. Bolt (4) E. 5/16” Nylon Lock Nut (5) C. 5/16” x 1” Bolt (2) Figure 9. Idler Arm Installation A. Belt Guard E. 5/16” Fender Washer B. 5/16-18 x 1” Bolt F. Pivot Spacer C. 5/16” Washer G. Idler Arm Assembly D. 5/16-18 x 1-3/4” Bolt H. 5/16-18 Flange Nut 3. Remove the two 7/16” bolts and hex nuts from the inside bearing. Remove the bearing from the blower housing and discard the two hex nuts. 4. Install the blower mount plate (A, Figure 10) onto the back plate of the blower. Install the 5/16-18 x 3/4” self-tapping bolts (B), but do not tighten until all screws have been started. Tighten securely. 5. Install three 5/16-18 x 3/4” bolts (D) near the bearing. Install the two 5/16-18 x 1” bolts (C) in the two remaining holes. Note the direction of the bolts, this is critical. Secure with the 5/16-18 nylon lock nuts (E) as shown. ABCDEFGHACCEEBEBD 7 48” & 52” Blower Mount & Drive Installation 6. Install the bearing (B, Figure 11) on the shaft with the grease fitting pointing towards the discharge of the blower. Secure with the 7/16-14 x 1-1/2” bolts (A) and 7/16-14 nylon lock nuts (C) as shown. Tighten the setscrew in the collar of the bearing. 7. Install the spring (G) on the bolt of the idler arm and secure with a 5/16-18 nylon lock nut (H). Only tighten the nut until the threads come through the nylon. Do not clamp spring. 8. Hook the spring on the eyebolt (F). Install the eyebolt and 1/4” washer (E) on the blower mount plate and secure with the nylon nut (D) as shown. The nylon nut (D) must be fully tightened so the eyebolt is drawn up tight against the mount. The eyebolt must be vertical. ABCDEFGH Figure 11. Install Bearing & Eyebolt A. 7/16” x 1-1/2” Capscrew (4) E. 1/4” Washer B. BearingF. 1/4” x 1” Eyebolt C. 7/16” Nylon Lock Nut (4) G. Spring D. 1/4-20 Nylon Lock Nut H. 5/16-18 Nylon Lock Nut 9. Install the blower pulley and key with the hub facing INWARD towards the bearing, and hold against the bearing. Tighten set screws. 10. Install one 3/8-16 flange nut on the 3/8-16 x 6” bolt and tighten against the end of the threads (see Figure 12). Install drive belt on the drive pulley and install the 3/8-16 x 6” bolt. Leave enough space between the belt and bolt so it will not interfere. Secure the bolt with a 3/8” serrated flange nut. Figure 12. Install Blower Pulley & Guide Bolt 11. Loosen the idler pulleys and install the belt under the belt keeps. Make sure the groove of the belt is properly seated in the v-pulleys (see Figure 13, the gray section is the flat side of the belt). Reposition the belt keeps so they will not interfere with the drive belt and tighten the idler pulleys. Figure 13. Belt Routing 8 48” & 52” Blower Mount & Drive Installation Install Blower & Belt Guard 1. Install the blower onto the chute mount tabs with the blower mount tabs towards the rear. Secure with the retainer pin and hair pin. Make sure the handle of the retaining pin is pointing down. 2. Pull the idler arm lever against the spring to install the drive belt on the spindle pulley. The tension idler should be approximately 3/4” - 1” away from the blower housing when belt in installed. If not, remove the drive belt and reposition the top idler pulley in the outside row of holes until the measurement is achieved. 3. Install the blower belt shield and secure with the 5/16” x 1” bolts and 5/16” washers. 4. Install the guard cover and secure with the plastic knobs. Figure 14. Install Blower & Belt Guard 9 Initial Installation & Assembly 61” TRIPLE-BAG COLLECTION SYSTEM BLOWER MOUNT & DRIVE GROUP Remove Discharge Chute 1. Park machine on a flat, level surface and apply the parking brake. 2. Remove the discharge chute and save. Save springs and spacer (Derby Stallion only). Release Mower Drive Belt Tension 1. Raise the floor pan and loosen the spring compression nut (A, Figure 20) to release the belt tension. Remove Guard & Spindle Pulley 1. Remove the right-hand belt guard (A, Figure 21) and save. Remove and discard the two front 5/16-18 x 1” bolts (G), 5/16” washers (F) and 5/16” body clips. 2. Remove the mower deck drive belt from the right- hand spindle pulley. 3. Remove the right-hand spindle pulley (D), 5/8”: nylon lock nut (B), 5/8” washer (C) and 1/4” key (E). Use a block of wood to keep the blade from spinning while removing the 5/8” nut. Figure 19. Chute Removal Figure 20. PTO Mower Drive Belt A. Spring Compression Nut B. Idler Spring BA Figure 21. Belt Guard & Pulley Removal A. Guard E. Key B. 5/8” Nylon Lock Nut F. 5/16” Washer (3) C. 5/8” Washer G. 5/16-18 x 1” Bolt (3) D. Spindle Pulley ABCDEGF 10 61” Blower Mount & Drive Installation Install Spindle Pulley 1. Apply an anti-seize compound to the spindle shaft. Install the new, double spindle pulley (C, Figure 22) on the shaft with the smaller pulley facing up with the 5/8” nylon lock nut (A), 5/8” washer (B) and 1/4” key (D) and tighten to 85-95 ft./lb...
Dieses Handbuch ist für folgende Modelle:Handrasenmäher - 1000z Series (913.28 kb)