Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Hersteller: Agri-Fab Dateigröße: 2.99 mb Dateiname: Unterrichtssprache:

NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the inner nut on the Clutch Cable. • Tighten the outer nut on the Clutch Cable. TO DECREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the outer nut on the Clutch Cable. • Tighten the inner nut on the Clutch Cable. • Repeat the above procedure until you have the correct tension. FIG. 2 10 11 ASSEMBLY ROLLER 1/2 X 7 HEX BOLT REAR ROLLER.. MOUNTING BRACKET 5/16 X 3/4 HEX BOLTS.. AND 5/16 HEX LOCK NUTS 1/2 HEX LOCK NUT INSTALL REAR ROLLER TO DECK • Install Rear Roller Mounting Bracket to rear of deck using two 5/16 x 3/4 Hex Bolts and two 5/16 Hex Lock Nuts. (See Fig. 3.) • Install Roller to Rear Roller Bracket using 1/2 x 7 Hex Bolt and 1/2 Hex Lock Nut. • Make sure Roller turns freely on Bolt. FIG. 3 12 OPERATION HEIGHT ADJUSTMENT STRAP HEIGHT ADJUSTMENT LIFT LEVER RECOIL START HANDLE MOWER BLADE.. CLUTCH LEVER SHUT OFF.. CONTROL TOW HITCH OFFSET.. ADJUSTMENT TOW BAR HEIGHT.. ADJUSTMENT FIG. 4 OPERATION 13 OPERATION GROUND LEVEL CUTTING HEIGHT CUTTING HEIGHTS HEIGHT ADJUSTMENT STRAP HEIGHT ADJUSTMENT LIFT LEVER LOCATING PIN HAIR COTTER PIN CLEVIS PIN TOW BAR ADJUSTMENT TOW BAR HAIR COTTER PIN 1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 4-1/2" 5" FIG. 6 14 OPERATION This mower has been designed to run offset from the center of the tow vehicle. This allows the operator to drive along side high brush with the tow vehicle while cutting down the brush beside him. The adjustable hitch gives you three offset cutting positions plus straight behind for narrow paths. MODEL 45-03071 The adjustable hitch of this mower can be set in seven positions including straight and offsets of 15", 29" and 39" on both sides. MODEL 45-0361 The adjustable hitch of this mower can be set in seven positions including straight and offsets of 9", 17" and 23" on both sides. 15 OPERATION 16 17 CUSTOMER RESPONSIBILITIES WHEEL PIVOT 3 WHEEL 2 QUADRANT 3 SPINDLE 2 SWIVEL 2 WHEEL PIVOT 3 WHEEL 2 .. CUSTOMER RESPONSIBILITIES BLADE CARE AND SERVICE CAUTION: DO NOT HANDLE MOWER BLADES WITH BARE HANDS. CARELESS OR IMPROPER HANDLING MAY RESULT IN SERIOUS INJURY. BLADE CARE For best results mower blades must be kept sharp. The blades can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen blades while they are still on the mower. BLADE SERVICE (Refer to fig. 9) TO REMOVE BLADE ASSEMBLY FROM DECK • Remove cotter pin from the spindle shaft. • Remove nut and washer from the spindle shaft. • Pull blade assembly off the spindle shaft. (Watch for a key in the spindle shaft.) TO REMOVE BLADES FROM BLADE ASSEMBLY. • Remove cotter pin from the blade bolt. • Remove nut from the blade bolt. • Remove blade from the blade assembly. BLADE SHARPENING • Blades can be sharpened with a file or grinding wheel. NOTE: When sharpening blades take care to maintain blade balance. Sharpen both blades equally even if one blade does not need to be sharpened. Check balance by weighing each blade to make sure they are equal in weight. CAUTION: IF YOUR BLADE BOLTS SHOW WEAR, REPLACE THEM WITH FACTORY REPLACEMENTS ONLY. TO REINSTALL BLADES • Assemble a blade bolt through a flat washer, a blade and then another flat washer. • Assemble the bolt through the hole in the stump plate and the blade hub assembly. • Assemble a flat washer and nut onto the blade bolt. • Tighten nut, then loosen just until blade can pivot. • Install a cotter pin to secure the nut. TO REINSTALL BLADE ASSEMBLY TO MOWER • Reinstall key in spindle shaft, if necessary. • Install the blade assembly onto the spindle shaft. • Secure with flat washer and nut. • Torque the spindle shaft and nut to 15 FT. LBS. and secure with a hair cotter pin. BLADE ASSEMBLY FIG. 9 WARNING: SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS OR REPAIRS TO THE MOWER. CLEANING THE MOWER Water pressure from a garden hose will remove fresh clippings from the underside of the mower. Clean mower after each mowing. DAILY MAINTENANCE Make sure all nuts and bolts are tight, cotter pins and retainer springs are secure. Keep blade...

Herunterladen

Geben Sie zwei Ziffern: