Login:
Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Anleitung Hustler Turf, modell 3500

Hersteller: Hustler Turf
Dateigröße: 27.87 mb
Dateiname: 109627.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Daily inspect mower for grass clippings and wire and string tangles. The underside of the mower deck will collect a build-up of grass clippings and dirt, especially when grass is wet or has high moisture content. This build-up will harden, restricting blade and air movement and will probably show a poorer quality of cutting. Therefore it should be removed routinely. To do this it will be necessary to raise and block the deck, using jack stands or blocks, in the full up position and scrape the build-up from underneath. Refer to the deck owner’s manual for more detailed information. Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Hustler service center when assistance is needed. Torque values IMPORTANT: WARNING: Particular attention must be given to tightening the drive wheel lug bolts and blade spindle bolts. Failure to correctly torque these items may result in the loss of a wheel or blade, which can cause serious damage or personal injury. Torque values are given below: Ft-lbs. Nm Wheel (lug) bolts - front . . . . 85-95 . . . . . . 115-129 Wheel (lug) bolts - rear . . . . . 65-75 . . . . . . 88.1-101.7 Deck blade (top) bolts . . . . . . 65-75 . . . . . . 88.1-101.7 Deck blade (bottom) bolts . . . 118 . . . . . . . . 160.01 Lug bolts only - It is recommended that these be checked after the first 2 hours of operation, initially, every 50 hours and following removal for repair or replacement. For all other torques refer to the various tractor parts manuals for standard torque chart. See the Product Literature section of this manual for ordering information. For engine torque values, see engine service manual. Tires It is important that the tires have an equal amount of air pressure. The recommended pressure are: Front wheels. . . . . . . . . . . . 14-18 psi (96-124 KPa) Rear wheels . . . . . . . . . . . .14-18 psi (96-124 KPa) Solid fill tires are not recommended for Hustler turf equipment. On any machine, with solid filled tires, the warranty claim will be denied. Lubrication Engine Oil . . . . . . . . . . . . . . .See Chart below Transmission Oil . . . . . . . . . .ISO VG 46 Grease . . . . . . . . . . . . . . . . . .SAE multi-purpose grease Recommended oils Ambient Temperature Recommended oil + 40° — 120°F (+4.4° — 48.9°C) SAE 30W + 10° — 120°F (+12.2° — 48.9°C) SAE 15W-40 – 10° — 120°F (-23.3° — 48.9°C) SAE 10W-30 – 20° — 60°F (-28.9° — -15.6°C) SAE 5W-30 NOTE: Engine originally shipped with 10W-30 oil. Lubrication fittings NOTE: After every 50 hours of normal operation, apply a good quality grease to the lubrication points listed below (refer to the Recommended Lubricants chart). When operating under extremely dirty conditions, lubricate more frequently than every 50 hours. • Lift cylinder • Front Lift arm • Power Steering Cylinder • Brake pedal shaft • Differential Lock pedal shaft To lubricate these points: 1. Wipe away all old grease and dirt from the lubrication fittings to prevent dirt or foreign material from entering as new grease is applied. 2. Use a high pressure grease gun to force in the new grease. Apply pressure until clean grease oozes from each lubrication point. 3. Wipe away any excess grease. Service access Opening the hood WARNING: To avoid personal injury from contact with moving parts: Never open the hood and seat while the engine is running. Do not touch the muffler or exhaust pipe while they are hot; severe burns could result. Unlock the hood latch. Raise the hood using the hood handle. Figure 4-1 Close the hood and clamp the hood latch. Opening the seat platform Pull out on the seat release knob and pivot the seat platform forward. Figure 4-2 Electrical system The electrical system is a 12-volt DC system with negative ground. The recommended battery size is a BCI group 35, 12-volt battery with a minimum cold cranking ability of 490 amps at -18°C (0°F). A maintenance-free battery is recommended. Otherwise, follow battery manufacturer’s maintenance, safety, storing and charging specifications. Refer to Maintenance Locator Chart found elsewhere in this manual. 4-2 109627_0910 Alternator cleaned periodically. - - Hood latch Hood latch Always wear eye protection when checking the battery, acid can cause serious injury to skin and eyes. If contact occurs, flush area with clean water and call physician immediately. Acid will also damage clothing. Do not drink the battery electrolyte. Do not allow open flame near the battery when charging. Hydrogen gas forms inside the battery. This gas is both toxic and flammable and may cause an explosion if exposed to flame. Always remove the negative ground first and replace it last. Do not overfill battery. Electrolyte may overflow and damage paint, wiring or structure. When cleaning the battery, use soap and water. Be careful not to get soap and water into the battery. Clean the battery terminals with a solution of four parts water and one part baking soda when they bec...

Dieses Handbuch ist für folgende Modelle:
Handrasenmäher - 3700 (27.87 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien