Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Bosch Dateigröße: 78.13 kb Dateiname: Unterrichtssprache:

Stainless Steel Surfaces: Wipe and dry stainless steel in the same direction as the grain. Avoid using too much pressure, which may mar the surface. To remove finger prints and give added shine, use spray cleaners such as Stainless Steel Magic®. Do not allow any cleaning compounds to remain in contact with stainless steel for extended periods. Filters The hood has removable aluminum filters that must be cleaned when they collect grease. The filters can be cleaned with soap and water or in the dishwasher. DAH95 models are equipped with a filter light that will illuminate after 40 hours of operation. The light indicates that the filters need to be cleaned.When used over a wok or other high grease application, more frequent cleaning may be required. Remove the filters for cleaning: push the handle in and pull down. The front will come out first. Then pull the back down and out. See Figure 2. Lights NOTE: Turn off the lights and fan and allow lights to cool before handling. If lights do not operate upon installation, check for proper insertion. Light bulbs can be cleaned with soap and water. CAUTION DO NOT TOUCH THE BULBS IMMEDIATELY AFTER USE. THE BULBS WILL REMAIN HOT FOR SEVERAL MINUTES. Light Bulb Replacement Remove the damaged light bulb by turning counter-clockwise. Replace with a new 50W flood light bulb. Models DAH95 and DAH94 use a Par 20 halogen light bulb. Model DAH93 requires a R20 incandescent bulb. Follow package directions. Buttons Wipe with sudsy water or household cleaners such as Fantastic® or Formula 409®, rinse well and dry with a clean soft cloth to avoid water marks. WARNING Be sure the entire hood (including the filters and light bulbs) has cooled and grease has solidified before attmepting to clean any part of the appliance. 1 Do not use cooktop while hood is disassembled. Figure 2 - Filters DO NOT use the following! Do not use the following cleaning agents on any of the hood components: Abrasive Pads such as those made from steel wool (SOS®, Brillo®) or plastic mesh. Abrasive cleaners such as Comet®, Ajax® and Zud®. Flammable products such as gasoline or kerosene. PAGE 4 Troubleshooting Before calling service, check the possible explanations below. If these solutions fail, call Bosch service at 800-944-2904. Please have your serial number and model number ready. They are located on the underside of the hood on the left side. Problem Possible Explanations Noise during operation. Some noise is normal due to vibration and air movement. Excessive noise indicates one of the following: • Ductwork is too small/ undersized. • Ductwork is too big/ oversized. • Ductwork is loose. • Transtition is too small/ too loose. • Togglebolts are not tightened. • Loose screws in trim parts, ect. Noise when not operating. Backflow flap on outside of duct wall cap moves with the wind. Fan motor does not work. Power supply to hood is not sufficient. Wires are not completely connected. Filter light does not turn off (DAH95 models only). Light must be reset: hold filter button down for 3 seconds (Always clean filters before resetting filter light). Filter light does not turn on (DAH95 models only). Filter light will not come on until after 40 hours of operation. Filter light comes on. (DAH95 models only). Indicates that filters should be cleaned. Hold button down for 3 seconds to reset. Lights under hood hum. A slight hum is normal. Operation of hood trips breaker. • Wiring is not correct. • Circuit is not correct. One light above Speed button blinks (DAH95 models only). Conditions exceed allowable temperatures. Turn on next speed level. All three lights above Speed button blink (DAH95 models only). Heat sensor is not working. Call service. PAGE 5 Warranty Bosch Warranty The warranties provided by BSH Home Appliances Corp. in this Statement of Limited Warranty apply only to the BSH Ventilation Hood ("hood") sold to you, the first using purchaser, provided that the hood was purchased (1) for your use and not for resale and (2) in the United States or Canada and is located in the country of purchase. As used in this Statement of Limited Warranty, the term "Date of Installation" shall refer to the earlier of the date the hood is installed or ten (10) business days after the date the hood is sold to the first using purchaser, the warranties stated herein apply only to the first using purchaser and are not transferable. Standard Limited Warranty BSH warrants that its hood is free from defects in materials and workmanship for a period of twelve (12) months from the Date of Installation. During the warranty period, BSH or its authorized service center will repair or replace, at its sole option, any hood that proves to have been defective under conditions of normal use without charge. All removed parts and components shall become the property of BSH, at BSH's option. All replaced and/or repaired parts shall assume the identity of the original part for purposes of this warranty and this warranty shall not be extended wit...

Herunterladen

Geben Sie zwei Ziffern: