Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. DISPOSAL OF LITHIUM ION BATTERY. LITHIUM ION BATTERY. DISPOSE OF PROPERLY. You can return your unwanted lithium ion batteries to your nearest Sony Service Center or Factory Service Center. Note In some areas the disposal of lithium ion batteries in household or business trash may be prohibited. For the Sony Service Center nearest you call 1-800-222-SONY (United States only) For the Sony Factory Service Center nearest you call 416-499-SONY (Canada only) Caution Do not handle damaged or leaking lithium ion battery. Features •The battery IR light can be used on a camcorder with the NightShot function. Using the battery IR light, you can record more distant subjects in NightShot operation. •If your camcorder doesn’t have the accessory shoe attached, you can record with the battery IR light using the shoe bracket. Precautions •Avoid placing the battery IR light near combustible or volatile solvents such as alcohol or benzine. •Do not let any solid object or liquid fall onto or into the battery IR light. •Do not pick up the camcorder by the head of the battery IR light. •Remove the battery IR light and shoe bracket before putting the camera into a carrying case. •Avoid placing or storing the battery IR light in locations that are – Extremely hot such as in a car parked in the sun – In areas subject to direct sunlight or sources of high temperature, such a heating device – Vibrating •Remove the battery pack after using or when carrying the battery IR light. After use • Be sure to set the POWER switch to OFF. • Store in pouch after making sure that the unit is cool enough to handle. On cleaning Clean the battery IR light with a dry soft cloth. You can remove stubborn stains with a cloth lightly dampered with a mild detergent solution, then dry the unit with a soft cloth. Never use strong solvents, such as thinner or benzine, since these will damage the finish on the surface. Specifications IR light segment Power requirements 7.2 V DC Maximum power consumption 2 W Continuous lighting time Type of battery Lighting duration pack (min.) NP-F330 180 NP-F550 360 NP-F750 760 NP-F950 1,120 (Approx. minutes using fully-charged battery pack) Type of dry Lighting duration battery (min.) LR6 (size AA) 60 (Approx.minutes using two new dry batteries.) Illumination distance Approx. 3-20 m Dimensions Approx. 46 . 102 . 43 mm (1 13/16 . 4 1/8 . 1 3/4 inches) (w/h/d) Mass Approx. 90 g (3 oz) Accessories (supplied) shoe bracket (1) Operating instructions (1) Design and specifications are subject to change without notice. AUsing with the rechargeable battery The rechargeable battery pack is to be set at the behind of the battery IR light, and it is indicated as the BATT- . To attach the rechargeable battery Attach the fully charged battery to the battery IR light in the direction of the arrow. To remove the rechargeable battery While sliding the BATT RELEASE button on the battery IR light, slide out the battery in the direction of the arrow. BUsing with the dry batteries The dry batteries are to be set inside of the battery IR light, and they are indicated as the BATT- . (marked on the center of the battery compartment) 1 Slide the lid in the direction of the arrow 1. 2 Open the lid in the direction of the arrow 2. 3 Insert both of the size LR6 (AA) batteries with correct polarity. 4 Lift up and close the lid in the direction of the arrow 3. 5 Slide the lid in the direction of the arrow 4 until it clicks. Note on the dry battery Pay attention to the polality of the batteries when attaching. CAttaching the battery IR light to the camcorder Using supplied shoe bracket (illustration C-1) 1 Insert the battery IR light into the shoe in the direction of the arrow and slit on its bottom until it reaches the end. 2 Turn and tighten the lock knob to lock in the direction of the arrow. 3 Align the camcorder mounting screw with the hole on the bottom of the camcorder, and tighten the screw firmly. Using the accessory shoe of the camcorder (illustration C-2) 1 Insert the battery IR light into the shoe of the camcorder. 2 Follow the same procedure as above step 2. To remove the battery IR light Turn and loosen the lock knob to remove the battery IR light in the opposite direction of the arrow. DShooting in the dark (using the IR light) The IR light can be used on a camcorder with the NightShot function. For details of the NightShot operation, refer to the operating instructions supplied with the camcorder. 1 Set the POWER switch to BATT- or BATT- of the battery IR light while pushing the small green button. The IR indicator A lights up. 2 Slide the NIGHTSHOT switch on the cam...