Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Do not try to establish a connection between the camera and computer before installing the USB driver onto the computer. If you do, the computer will not be able to recognize the camera. • USB driver installation is required in the case of Windows 98SE and 98. Do not connect the camera to a computer running one of the above operating systems without installing the USB driver first. • USB driver installation is not required in the case of Windows XP, 2000, and Me. 1. What you should do first depends on whether your computer is running under Windows XP, 2000, Me, 98SE, or 98. Windows 98SE/98 Users • Start from step 2 to install the USB driver. • Note that the example installation presented here uses Windows 98. Windows XP/2000/Me Users • Installation of the USB driver is not required, so jump directly to step 6. 177 VIEWING IMAGES ON A COMPUTER 2. Set the bundled CD-ROM into the CD-ROM drive of your computer. • Use the CD-ROM whose contents label shows “USB driver”. 3. On the menu screen that appears, click “English”. 4. Click [USB driver B] and then [Install]. • This starts installation. • Follow the instructions that appear on your computer screen to complete the installation. • The following steps show installation under the English version of Windows. 5. When the final setup screen appears, click the [Exit] button on the CD-ROM menu to exit the menu, and then remove the CD-ROM from your computer. • With some computer operating systems, a message prompting you to restart your computer may appear. If this happens, restart your computer. The CD-ROM menu will appear again after your computer restarts. Click the [Exit] button on the CD-ROM menu to exit the menu, and then remove the CD-ROM from your computer. 6. Connect the bundled AC adaptor to the [DC IN 5.3V] connector of the USB cradle, and then plug it in to a household power outlet. • If you are using battery power without the AC adaptor, make sure that the battery is fully charged. • Note that the shape of the AC adaptor depends on the area where you purchased the camera. 178 VIEWING IMAGES ON A COMPUTER [DC IN 5.3V] 7. Connect the USB cable that comes bundled with the camera to the USB cradle and your computer’s USB port. USB cable (bundled) Connector B USB port 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 [DC IN 5.3V] • Take care when connecting the USB cable to the USB cradle or your computer. USB ports and cable plugs are shaped for proper positioning. • Plug the USB cable plugs into the ports securely, as far as they will go. Proper operation is not possible if connections are not correct. Connector A [ ](USB port) 179 VIEWING IMAGES ON A COMPUTER 8. Press the camera’s power button to turn it on, and then press its [MENU] button. 9. Select the “Set Up” tab, select “USB”, and then press []. 10. Use [] and [] to select “Mass Storage (USB DIRECT-PRINT)”, and then press [SET]. 11. Turn off the camera. 12. Place the camera onto the USB cradle. • Do not place the camera onto the USB cradle while it is turned on. 13. Press the USB cradle’s [USB] button. • This will cause your computer to create a hardware profile for camera’s built-in memory or the memory card loaded in the camera. You do not need to install the USB driver every time. After you install it once, your computer will recognize the camera’s built-in memory or its memory card when you establish a USB connection between the camera and your computer. 180 VIEWING IMAGES ON A COMPUTER • Pressing the [USB] button enters the USB mode, which causes the USB cradle’s [USB] lamp to light green (page 213). • At this point, some operating systems will display a “Removable Disk” dialog box. If your operating system does, close the dialog box. [USB] button [USB] lamp 14. On your computer, double-click “My Computer”. • If you are running Windows XP, click [Start] and then [My Computer]. 15. Double-click “Removable Disk”. • Your computer sees the camera’s file memory as a removable disk. 16. Double-click the “Dcim” folder. 17. Double-click the folder that contains the image you want. 18. Double-click the file that contains the image you want to view. • For information about file names, see “Memory Folder Structure” on page 190. NOTE • If you open a rotated image on your computer, the original unrotated version will appear (page 133). This is true both for a rotated image opened from camera memory and for a rotated image that has been copied to your computer’s hard disk. 181 VIEWING IMAGES ON A COMPUTER 19. Depending on your operating system, perform one of the following procedures to save the files, if you want. Windows 2000, Me, 98SE, 98 1. In the camera’s file memory (Removable Disk), right- click the “Dcim” folder. 2. On the shortcut menu that appears, click [Copy]. 3. Double click [My Documents] to open it. 4. On the My Documents [Edit] menu, click [Paste]. • This copies the “Dcim” folder (which contains the image files) to your “My Documents” folder. Windows XP 1. In the camera’s file memory (Remo...